Samsung MultiXpress K4 Series Service Manual Download

Page: 396 / 526

4. Troubleshooting

4.6.16. Sx–xxxx (System error)

Error Code

Error Message

Troubleshooting Page

S1-1113

Video System Failure: #S1-1113. Turn off then on

P.4–162

S1-1114

Video System Failure: #S1-1114. Turn off then on

P.4–162

S1-1313

The clock became initial time. Set a time again

P.4–163

S1-2111

Video System Failure: #S1-2111. Turn off then on

P.4–163

S1-2411

HDD System Failure: #S1-2411. Turn off then on. Call for service if the
problem persists

P.4–164

S1-2421

HDD System Failure: #S1-2421. Turn off then on

P.4–164

S1-2422

HDD System Failure: #S1-2422. Turn off then on

P.4–164

S1-2510

MSOK Failure: #S1-2510. Call for service and change MSOK

P.4–164

S1-2511

MSOK System Failure: #S1-2511. Turn off then on

P.4–164

S1-2520

MSOK Failure: #S1-2520. Call for service

P.4–164

S1-2521

MSOK Failure: #S1-2521. Call for service

P.4–164

S1-2523

PPM data is incorrect. Call for service and change MSOK

P.4–164

S1-2540

MSOK Failure: #S1-2540. Call for service & change MSOK

P.4–164

S1-2550

MSOK Failure: #S1-2550. Call for service & change MSOK

P.4–164

S1-4111

Video System Failure: #S1-4111. Turn off then on

P.4–165

S1-4311

Video System Failure: #S1-4311. Turn off then on

P.4–165

S1-5221

Wireless network card is not installed. Install the card

P.4–165

S2-1211

Engine System Failure: #S2-1211. Turn off then on

P.4–166

S2-2311

Engine System Failure: #S2-2311. Turn off then on

P.4–166

S2-3321

Supplying and mixing toner to developer unit. Please wait...

P.4–166

S2-3421

Calibrating image density. Please wait...

P.4–166

S2-4210

Front door is open. Close it

P.4–167

S2-4410

Right door is open. Close it

P.4–168

S3-3121

Scanner locked or another problem occurred.(No Switch Case)Scanner is
locked

P.4–168

S3-3211

Scan System Failure: #S3-3211. Turn off then on

P.4–169

S3-3213

Scan System Failure: #S3-3213. Turn off then on

P.4–169

S3-3214

Scan System Failure: #S3-3214. Turn off then on

P.4–169

S3-3215

Scan System Failure: #S3-3215. Turn off then on

P.4–169

S3-3216

Scan System Failure: #S3-3216. Turn off then on

P.4–169

S3-3217

Scan System Failure: #S3-3217. Turn off then on

P.4–169

S4-3111

Fax System Failure: #S4-3111. Install fax modem card again

P.4–169

S5-3111

UI System Failure: #S5-3111. Call for service

P.4–170

S6-3122

Network cable is disconnected. Check it

P.4–171

S6-3123

This IP address conflicts with that of other system. Check it

P.4–171

S6-3128

802.1x authentication failed. Please contact the system administrator

P.4–171

S7-1110

Engine System Failure: #S7-1110. Turn off then on

P.4–172

S7-2110

Fuser Failure: #S7-2110. Turn off then on

P.4–172

4-161

Summary of Contents for MultiXpress K4 Series



























































































































































































































































































































































































































































































































Search results

Summary of Contents for MultiXpress K4 Series

Reviews:

Related manuals for MultiXpress K4 Series

Brands by name

Popular brands

Samsung MultiXpress K4 Series, Service Manual

Search results

Summary of Contents for MultiXpress K4 Series

Reviews:

Related manuals for MultiXpress K4 Series

Brands by name

Popular brands