Samsung MultiXpress K4 Series Service Manual Download | Manualshive

Page: 54 / 526

background image

2. Product Specifications and Description

2.6. Fuser unit

This section describes the image fusing process used by the machine.

2.6.1. Fuser Unit overview

This unit fuses the toner that was transferred by the transfer roller onto the paper, by applying heat and pressure to
complete fusing process. This machine applied the 2–Roller fusing system and used the thinner heat roller to improve
the warm-up time.

1)

Halogen Lamp

The fuser unit has two halogen lamps. One heats the center of the heat roller, the other heats the end of axial direction.
These halogen lamps are lit alternately to heat the heat roller. each lamp has its coil in a different location. The coil
of the center heater lamp is in the center, those of the side heater lamp are on both sides. The lamp s are fixed inside
of the heat roller. When rotating the heat roller, these lamps does not rotate.

2)

Heat Roller

The heat roller is made of the aluminum and gets heat from the halogen lamp and transfer it to toner and paper. The
thinner heat roller reduces the warm-up time and the mode switching time. To prevent the heat roller from adhering to
the toner, its surface applied the PFA coating. The gear located the side of the heat roller rotates the roller.

3)

Pressure Roller

The pressure roller is a rubber roller which ensures proper nip width between the pressure roller and heat roller. To
adhere the toner on paper effectively, the pressure roller pushes the heat roller by using the spring.

4)

NC sensor

NC sensors (non-contact type thermistors), located near the center of the heat roller, control the temperature.

5)

Thermistor

Thermistor detects the temperature on the surface of the heat roller and controls the halogen lamp.

2-38

Copyright© 1995-2017 SAMSUNG. All rights reserved.

«
...
52
53
54
55
56
...
»

Summary of Contents for MultiXpress K4 Series















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MultiXpress K4 Series

d-color mf752plus

Brand: Olivetti Pages: 37

Brand: Xerox Pages: 19

Brand: Toshiba Pages: 122

Brand: Infotec Pages: 98

Brand: Olivetti Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands