background image

14  English

Ins
tallation r

equir

ement

s

Installation requirements

CAUTION

Do not grasp the knob, handle and push when you install.

CAUTION

DO NOT

 install the oven so that the door is flush with the cabinet. 

For OTR over Gas Stove, please follow local GAS CODE.

Minimum dimensions

WARNING

If overhead cabinets are provided, a range hood should also be provided that 
projects horizontally a minimum of 5 in (12.7 cm) beyond the front of the cabinets. 
This will dissipate any heat buildup in the overhead cabinets to prevent death, 
personal injury, and/or fire hazard. The ventilating hood must be constructed of 
sheet metal not less than 0.0122” thick. Install above the cooktop with a clearance 
of not less than 1/4” between the hood and the underside of the combustible 
material or metal cabinet. The hood must be at least as wide as the appliance 
and centered over the appliance. Clearance between the cooking surface and the 
ventilation hood surface must never be less than 24 inches.

Exception 1 :

 Installation of a listed microwave oven or cooking appliance over the 

cooktop shall conform to the installations packed with that appliance.

• 

30 in (76.2 cm) minimum clearance between the top of the cooking surface and 
the bottom of an unprotected wood or metal cabinet or If no 30 in (76.2 cm) 
minimum clearance, 24 in (61 cm) minimum when the bottom of the wood or 
metal cabinet is protected by not less than 0.25 in (0.64 cm) flame-retardant 
millboard covered with not less than no. 28 MSG sheet steel, 0.015 in (0.038 cm) 
stainless steel, 0.024 in (0.061 cm) aluminum, or 0.020 in (0.051 cm) copper.

• 

18 in (45.7 cm) minimum between the countertop and the adjacent cabinet 
bottom.

Exception 2 :

 For island installation, maintain 2 - 1/2” minimum from cutout to 

back edge of countertop and 4” minimum from cutout to side edges of countertop.

IMPORTANT:

To eliminate the risk of burns or fire caused by reaching over heated surface 
units, avoid having cabinet storage space located above the surface units. If you 
have cabinet storage space over the heating elements, you can reduce the risk by 
installing a range hood that projects horizontally a minimum of 5 inches beyond 
the bottom of the cabinets.

01. DG68-01600A-00_IM_NSG6DG8700SRAA_EN_231102.indd   14

01. DG68-01600A-00_IM_NSG6DG8700SRAA_EN_231102.indd   14

2023-11-06   오전 11:47:47

2023-11-06   오전 11:47:47

Summary of Contents for NSG6D 8 Series



























Reviews: