background image

24  English

Ins
tallation ins

truc

tions

Installation instructions

Checking the flame quality:

All combustion flames need to be visually checked to determine their flame 
quality.

2

3

1

1. 

Soft blue flames 

— Normal for natural gas 

operation.

2. 

Yellow tips on outer cones 

— Normal for 

LP gas operation.

3. 

Yellow flames 

— Abnormal for any gas 

operation; call for service.

NOTE

If burner flame looks like 3, the range 
should not be used until it is serviced. Call 
for service. Normal burner flames shall look 
like 1 or 2, depending on the gas type you 
use.

Step 9. Final installation checklist

You have just completed installing your range. Make sure all controls are in the off 
position and the flow of ventilation air to the range is unobstructed. The following 
is a checklist to confirm your range is safely installed and ready for operation.

Gas Range Plug

Locking screw

• 

Gas line has been properly connected to 
the range. The gas has been turned on. All 
connections have been checked for leaks.

• 

Range is plugged into the properly 
grounded electrical receptacle.

• 

Approved anti-tip bracket is properly 
installed and engaged with the range.

• 

Range is leveled and is firmly sitting on a 
solid, level floor.

• 

Gas surface burners have been properly 
assembled.

• 

All burners have been tested for proper 
operation.

• 

FOR INSTALLER ONLY—Check and/or 
adjust the broil and oven burner flames as 
described on pages 22 - 23 in this manual.

Adjusting the oven burner air adjustment shutters

Air 

adjustment 

shutter

All oven burners have an air adjustment 
shutter. The purpose of the shutter is to 
regulate the flow of air to the flames. 
Properly adjusted flames should burn 
steadily with approximately 1 in of blue 
cone. The flames should never extend 
past the edge of the burner baffles. Even 
though these are preset at the factory, they 
should be checked and, if needed, adjusted 
periodically to ensure efficient operation.

01. DG68-01600A-00_IM_NSG6DG8700SRAA_EN_231102.indd   24

01. DG68-01600A-00_IM_NSG6DG8700SRAA_EN_231102.indd   24

2023-11-06   오전 11:47:50

2023-11-06   오전 11:47:50

Summary of Contents for NSG6D 8 Series



























Reviews: