24 English
Installation instructions
Installation instructions
Step 4. Install the anti-tip device
WARNING
To reduce the risk of tipping, the appliance must be secured by properly installing
the anti-tip device packed with the appliance.
• All ranges can tip, resulting in personal injury.
• Tipping ranges can cause burns from spills, personal injury, and/or death.
• To prevent accidental tipping, install and check the anti-tip bracket following
the instructions and template supplied with the bracket.
An anti-tip bracket and screws, installation
instructions, and template are shipped
with every range (PN DG94-00870B). The
instructions include information necessary
to complete the installation of the anti-tip
bracket. Read and follow the instructions on
the sheet and use the template for anti-tip
bracket installation. If not properly installed,
the range could be tipped by you or a child
standing, sitting, or leaning on an open
oven door.
NOTE
To install an anti-tip bracket, release and extend the leveling leg to a minimum
clearance of 21/32” (16.5 mm) between the range bottom and the floor.
To check if the bracket is installed and engaged properly, remove the warming
drawer or storage drawer and look underneath the range to see that the leveling
leg is engaged in the bracket. Carefully tip the range forward. The bracket should
stop the range within 4” (10.2 cm) of tipping. If it does not, the bracket must be
reinstalled.
If the range is pulled from the wall for any reason, always repeat this procedure
to verify the range is properly secured by the anti-tip bracket. Never completely
remove the leveling legs or the range will not be secured to the anti-tip device
properly.
Step 3. Convert to lp gas (optional)
All new gas ranges are shipped from the factory set up to use natural gas. Any
Samsung gas range can be converted to use LP gas. Refer to page 80 in the User
Manual to contact a qualified service technician.
The conversion process should only be performed by a qualified LP gas installer.
Conversion instructions and LP orifices will be supplied with the LP conversion kit.
The conversion to LP requires all burner orifices to be changed (5 surface burners
and 2 oven burners).
In addition, the nozzle on the gas pressure regulator needs to be reversed. All
replaced orifices must be left with the consumer, including the instructions and
retrofit sizes and orifice indication.
BURNER ORIFICE SIZES AND OUTPUT
RATINGS
(LP Gas [Propane] 10 in WCP)
BURNER ORIFICE SIZES AND OUTPUT
RATINGS
(Natural Gas 5 in WCP)
Burner
Location
BTU Rate
Orifice
Size [mm]
Burner
Location
BTU Rate
Orifice
Size [mm]
RF¹
14,500
1.12
RF¹
18,000
1.92
RF²
12,500
1.06
RF²
17,000
1.92
RF3
14,500
1.12
RF3
18,000
1.92
LF¹
11,500
1.04
LF
15,000
1.78
LF²
10,000
0.98
RR
5,000
1.01
LF3
10,000
0.98
LR
9,500
1.40
RR
4,000
0.62
CTR
9,500
1.38
LR
7,500
0.83
BAKE
18,000
1.90
CTR
7,500
0.83
BROIL
13,500
1.64
BAKE
15,000
1.15
BROIL
11,500
1.02
¹ Model NX58*565***
² Model NX58*560***
3 Model NX58*751***
Install_NX58H56_DG68-00524A-13_EN+MES+CFR.indb 24
Install_NX58H56_DG68-00524A-13_EN+MES+CFR.indb 24
2020-10-13 11:50:33
2020-10-13 11:50:33