English 21
Ins
tallation ins
truc
tions
Step 4. Install the anti-tip device
WARNING
To reduce the risk of tipping, the appliance must be secured by properly installing
the anti-tip device packed with the appliance.
•
All ranges can tip, resulting in personal injury.
•
Tipping ranges can cause burns from spills, personal injury, and/or death.
•
To prevent accidental tipping, install and check the anti-tip bracket following the
instructions and template supplied with the bracket.
An anti-tip bracket and screws, installation
instructions, and template are shipped
with every range (PN DG94-00870B). The
instructions include information necessary
to complete the installation of the anti-tip
bracket. Read and follow the instructions on
the sheet and use the template for anti-tip
bracket installation. If not properly installed,
the range could be tipped by you or a child
standing, sitting, or leaning on an open oven
door.
*approximately
21
/
32
” (16.5 mm)
Screw must enter
wood or concrete
Anti-Tip
bracket
*NOTE:
To install the Anti-Tip
bracket, release the leveling
leg. A minimum clearance of
21
/
32
” (16.5 mm) is required
between the range bottom
and the kitchen floor.
To check if the bracket is installed and engaged properly, remove storage drawer
and look underneath the range to see that the leveling leg is engaged in the
bracket. Carefully tip the range forward. The bracket should stop the range within
4 inches (10.2 cm) of tipping. If it does not, the bracket must be reinstalled.
If the range is pulled from the wall for any reason, always repeat this procedure
to verify the range is properly secured by the anti-tip bracket. Never completely
remove the leveling legs or the range will not be secured to the anti-tip device
properly.
Step 5. Plug in and place
WARNING
BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 17
~ 18 in this manual. Improper connection of the grounding plug can result in a risk
of electric shock.
• All gas ranges come with a power cord.
The power cord is connected to the rear
of the range. Please review “Electrical requirements” on pages 17 ~ 18.
•
The electrical system, including the power cord, is preinstalled and prewired at
the factory. Altering any part of this system may result in a short or overload.
1.
Plug in the power cord. Make sure the outlet meets local or national electrical
codes as referenced on pages 17 ~ 18.
2.
Slide the range into place.
3.
Check the gas supply line to make sure it did not get damaged and it stayed
connected during positioning.
4.
Check to make sure the back leg of the range has slid into the anti-tip bracket.
Carefully tip the range forward to ensure that the anti-tip bracket engages the
back brace and prevents tip-over.
Install_NX60T9700_BEST_BETTER_AA_DG68-01243A-00_EN.indd 21
2020-03-26 6:41:24
Summary of Contents for NX60 8 Series
