Samsung OFFICESERV 500 Series Programming Manual Download

Page: 305 / 471

OfficeServ 500 Programming Guide

2-263

(Continued)

Option

Default

Description

15 INCOMING

ANSWER

If this option is set to YES, the duration of calls ringing
before answered will print on SMDR.

INTERCOM CALL

This option determines whether intercom calls will print
on SMDR.

KEY MMC IN/OUT NO

If set to YES then the SMDR record will show
programming being opened and closed in MMC 200 and
MMC 800.

20 HOTEL

PAGE

FEED

END

This option determines where the page feed is inserted
on HM REPT.(Hotel/Model Enabled Only)

21 HOTEL

START

LINE

This option determines that the number of empty lines per
each page on HM REPT.(Hotel/Model Enabled Only)

DID NUM/NAME

YES

If this option is set to YES, received DID information will
print on SMDR.

24 ITP

REGISTRATION

If set to YES then the SMDR record will show IP-based
station to system connect and disconnect.

25 SET

RELOCATION

If set to YES then the SMDR record will show set
relocated information.

CONDITIONS

NONE

INPUT CHARACTERS

Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.

DEFAULT DATA

SEE DESCRIPTION

SOME OPTIONS ARE DEPEND ON COUNTRY

Summary of Contents for OFFICESERV 500 Series
























































































































































































































































































































































































































































































Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands

Samsung OFFICESERV 500 Series, Programming Manual

Search results

Summary of Contents for OFFICESERV 500 Series

Reviews:

Related manuals for OFFICESERV 500 Series

Brands by name

Popular brands