Samsung OFFICESERV 500 Series Programming Manual Download | Manualshive

Page: 458 / 471

background image

CHAPTER 2.

Ошибка

!

Стиль

не

определен

.

2-416

© SAMSUNG Electronics Co., Ltd.

[856] TECH PROGRAMMING LOGS

This MMC lists the date, time and entry location of the last eight times that technician

programming was accessed. This will allow a technician to determine if there was

unauthorized access to system programming and where this access occurred.

The information stored in this log will consist of 2 elements, the date and time it occurred

at and the access location.

There are 4 types of access location information as described below:

Type

Description

NNNN

This would be the extension number of a phone that had accessed programming directly.

MODEM

This would indicate that programming was accessed by PCMMC via the integrated
V90 modem attached to the IOM board of main cabinet.

LAN

This would indicate that programming was accessed by PCMMC via the LAN
connection on the MCP2 card of main cabinet.

SIOx

This would indicate that programming was accessed by PCMMC via one of the SIO
connections on the IOM board of the main cabinet where x is the number(2 or 3) of
the SIO port that was used.

CONDITIONS

NONE

DEFAULT DATA

NONE

ACTION DISPLAY

1) Press Transfer button and enter 856.

Display shows:

(1) 11/22 11:03

Æ

201 :11/22 11:27

2) Enter index number.(e.g., 3)

OR

(3) 11/22 12:30

Æ

203 :11/22 13:30

Press Volume button to scroll.

3) Press Transfer button and enter to exit.

OR

Press Speaker button to advance next MMC.

RELATED ITEMS

MMC 800

ENABLE TECHNICIAN PROGRAM

«
...
456
457
458
459
460
...
»

Summary of Contents for OFFICESERV 500 Series
























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OFFICESERV 500 Series

Brand: R.V.R. Elettronica Pages: 38

Brand: iDance Pages: 10

Brand: texet Pages: 28

Brand: Teac Pages: 38

magicbox aavelin

Brand: ClearOne Pages: 93

Brand: CAME Pages: 28

AQUACIAT POWER LD 602R-3500R

Brand: CIAT Pages: 56

Brand: Barco Pages: 37

IX Room Systems XT Series

Brand: Avaya Pages: 41

bryant ONEBB3ZAC01

Brand: Carrier Pages: 6

Brand: EMX Industries, Inc. Pages: 19

Brand: RCA Pages: 28

Brand: Sharp Pages: 72

Ascotel IntelliGate 150

Brand: Aastra Pages: 5

Brand: Sharp Pages: 32

Brand: Sharp Pages: 116

Brand: Pioneer Pages: 8

Brand: Pioneer Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands