SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes
•
While on-hook, press
TRANSFER
and then dial
103
.
•
Dial
0
for Ringing,
1
for Auto Answer or
2
for Voice Announce.
•
Press
TRANSFER
to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have Forward
No Answer (FNA) turned on, you must answer screened transfers by pressing the
SEND
button before your FNA timer expires or the call will forward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
•
While on-hook, press
TRANSFER
and then dial
110
•
Dial
15
to access
AUTO ANS CO
.
•
Press the
VOLUME UP
or
DOWN
key to change status.
•
Press
TRANSFER
to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line button, route button or a flashing
CALL
button will automatically put your call on hold and connect you to the next call.
This feature can be turned on or off at your keyset.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
001
to turn Automatic Hold on or
000
to turn it off.
•
Press
TRANSFER
to store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing
TRANSFER
.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When using
headset mode, press the
SEND/END
button to answer and release calls.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
021
to use the headset or
020
to use the handset.
•
Press
TRANSFER
to store your selection.
44
45
Your keyset may be equipped with a Headset mode button. If it is so equipped
pressing this button while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the button while the
light is lit will cause the keyset to return to handset mode and the light will go out.
HOT KEYPAD
On your phone system your keyset’s keypad can be made “live” or “hot” so that it is
not necessary to lift the handset or press the
SPEAKER
button before you begin
dialing. Calls can be made and features activated by simply dialing the C.O. line
number, trunk group access code, intercom number or feature access code. To ac-
tivate this feature:
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
031
to turn the Hot Keypad on or
030
to turn it off.
•
Press
TRANSFER
to store your selection.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button on the
dial pad. This tone can be turned on or off.
•
While on-hook, press
TRANSFER
and then dial
110
.
•
Dial
040
to turn tones off or
041
to turn tones on.
•
Press
TRANSFER
to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal page
after you return your keyset to idle. To enable this feature:
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
051
to turn this feature on or
050
to turn it off.
•
Press
TRANSFER
to store your selection.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or press
the
SEND
button. This method will always answer calls in the order they arrived at
your keyset.When you turn ring preference off, you must press the flashing button
to answer a call, allowing you to answer calls in the order you choose.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
061
to turn ring preference on or
060
to turn it off.
•
Press
TRANSFER
to store your selection.
Table of Contents
ITP-5121D
Home Page
