background image

31

2. Dial the station number (e.g.,

205

) OR

[205] NO ANS FWD

press 

UP

or 

DOWN

key to select the 

010 SEC

station and press the right soft key OR 

OR

press 

ANS/RLS

to select all stations  

[ALL] NO ANS FWD

and press the right soft key

010 SEC

3. Press 

UP

or 

DOWN

key to select the

[205] DTMF DUR.

station timer and press the right soft key

0100 MS

4. Enter the new value via the dial pad,

[205] DTMF DUR.

e.g.,

0300

and the system will return 

0100 MS

0300

to step 2

5. Press 

TRSF

to store and exit 

programming OR press 

SPK

to store 

and advance to the next program

ADDING NAMES TO THE 
TRANSLATION TABLE

This program allows the system administrator or technician to associate a CID or
ANI number received from the Central Office with a name programmed in this
translation table. If there is no match between a received number and a name in
this table, [no CID name] or [no ANI name] will be displayed.

The translation table consists of 

1000

entries in the 

OfficeServ 500 M 

and

OfficeServ 7100,

and

OfficeServ 7200 

and

OfficeServ 7400 

systems or 

2000

entries in the

OfficeServ 500 L

system or 

500

entries in the 

OfficeServ 100

sys-

tem with each entry comprised of a ten digit telephone number and a 16 digit
name. See 

Program Station Names.

Open customer programming and follow the instructions below.

PROGRAM KEYS 

UP

DOWN - 

Used to scroll through options.

KEYPAD - 

Used to enter selections.

SOFT KEYS - 

Move cursor left and right.

SPK - 

Used to store data and advance to next MMC.

HOLD - 

Used to clear previous entry.

System_Administration_Guide.qxp  4/30/2007  12:56 PM  Page 38

Summary of Contents for OfficeServ 7000 Series















































Reviews: