•
Scroll to
STATION ON/OFF
and press
ENTER
—
OR
—you may dial 0 and
immediately enter the option.
•
Scroll to
HOT KEYPAD
, press
ENTER
to change option status.
•
Press
CANCEL
to enter change and return to Main Configuration Menu—
OR
—press
END
to return to idle screen.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button on the
dial pad. This tone can be turned on or off.
•
While on-hook, press
TRANSFER
and then dial
110
.
•
Dial
040
to turn tones off or
041
to turn tones on.
•
Press
TRANSFER
to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal page
after you return your keyset to idle. To enable this feature:
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
051
to turn this feature on or
050
to turn it off.
•
Press
TRANSFER
to store your selection.
From the LCD:
•
Press
MENU
button.
•
Scroll to
CONFIGURATION OPTION
and press
ENTER
.
•
Scroll to
STATION ON/OFF
and press
ENTER
—
OR
—you may dial
0
and
immediately enter the option.
•
Scroll to
PAGE REJOIN
, press
ENTER
to change option status.
•
Press
CANCEL
to enter change and return to the Main Configuration Menu—
OR
—press
END
to return to idle screen.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or press
the
ANS/RLS
button.This method will always answer calls in the order they arrived
at your keyset. When you turn ring preference off, you must press the flashing but-
ton to answer a call, allowing you to answer calls in the order you choose.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
061
to turn ring preference on or
060
to turn it off.
•
Press
TRANSFER
to store your selection.
53
52
•
Scroll to
STATION ON/OFF
and press
ENTER
—
OR
—you may dial 0 and
immediately enter the option.
•
Scroll to
AUTO HOLD
, press
ENTER
to change option status.
•
Press
CANCEL
to enter change and return to the Main Configuration Menu—
OR
—press
END
to return to idle screen.
NOTE: Intercom calls can be automatically put on hold by pressing
TRANSFER
.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When using
headset mode, press the
ANS/RLS
button to answer and release calls.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
021
to use the headset or
020
to use the handset.
•
Press
TRANSFER
to store your selection.
From the LCD:
•
Press
MENU
button.
•
Scroll to
CONFIGURATION
option and press
ENTER
.
•
Scroll to
STATION ON/OFF
and press
ENTER
—
OR
—you may dial
0
and
immediately enter the option.
•
Scroll to
HEADSET USE
and press
ENTER
to change option status.
•
Press
CANCEL
to enter change and return to Main Configuration Menu—
OR
—press
END
to return to idle screen.
Your keyset may be equipped with a Headset mode button. If it is so equipped
pressing this button while the button indicator is blank will cause the keyset to
enter headset mode and the button indicator to be lit solid to indicate this.
Pressing the button while the button indicator is lit solid will cause the keyset to
return to handset mode and the button indicator will go blank.
HOT KEYPAD
On your phone system your keyset’s keypad can be made “live” or “hot” so that it is
not necessary to lift the handset or press the
SPEAKER
button before you begin
dialing. Calls can be made and features activated by simply dialing the C.O. line
number, trunk group access code, intercom number or feature access code.
•
With the handset on-hook, press
TRANSFER
and then dial
110
.
•
Dial
031
to turn the Hot Keypad on or
030
to turn it off.
•
Press
TRANSFER
to store your selection.
From the LCD:
•
Press
MENU
button.
•
Scroll to
CONFIGURATION
option, press
ENTER
.
Home Page
ITP-5012L
Table of Contents
