Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two people lift and move the PDP TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
1
Connect the Guide Stand to the
Stand using four screws (M4 X L10)
as shown.
2
With your TV upright, connect the
TV to the Stand.
3
Fasten two screws (M4 X L12) at
position
1
, and then fasten two
screws (M4 X L12) at position
2
.
s
s
s
s
Rear
Front
s
s
s
s
1
2
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1.
Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2.
Install two AAA batteries.
✎
Make sure to match the + and -
ends of the batteries to the diagram in the battery compartment.
3.
Replace the cover.
Step 3
: Connect Power and Antenna or Cable
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12
AM EST.
To register this product, visit: www.samsung.com/
register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the
ENTER
E
button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
POWER
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control, select
the language for the On Screen
Display (OSD), and then press
the
ENTER
E
button.
P
2
Select
Home Use
, and then
press the
ENTER
E
button. If
you select
Store Demo
, the TV
will reset your picture and audio
settings every 30 minutes.
3
Select the
Antenna source
to memorize, you must select
Antenna Source
to same type
as your cable system type. After
selecting source, select
Start
;
then press the
ENTER
E
button
on your remote.
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
The TV memorizes the available
channels. This process can take
up to 45 minutes.
5
After the TV has memorized the
channels, choose the
Clock
Mode
. Select
Auto
if you have
a digital channel in your area.
Select
Manual
if you don’t, or
if you have a cable or satellite
box. When done, press the
ENTER
E
button.
✎
If you select
Manual
, the
clock setting screen appears.
6
Select the daylight savings time
setting:
Off, On
or
Auto
and then
press the
ENTER
E
button.
✎
This function is only available
when the
Clock Mode
is set to
Auto
.
7
Select the time zone in which you live, and then press the
ENTER
E
button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
The
Enjoy your TV.
screen appears. Then press the
ENTER
E
button.
If You Want to Rerun Plug & Play
1.
Press the
SOURCE
button on your remote, then select
TV
mode.
2.
Press the
MENU
button on your remote to display the menu.
3.
Press the
▲
or
▼
button to select
Setup
, and then press the
ENTER
E
button.
4.
Press the
ENTER
E
button again to select
Plug & Play
.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Top view
Front
Rear
Guide Stand
Screws (M4 X L10)
Stand
Rear
HDMI IN
3
HDMI OUT
AUDIO OUT
VIDEO OUT
AUDIO OUT
COMPONENT OUT
AUDIO OUT
DVI OUT
Using an HDMI to DVI Cable
HD connection (up to 720p/1080i)
Very Good Connection
Device
Best Connection
HD connection (up to 720p/1080i)
Using an HDMI Cable
DVD, Blu-ray player, HD cable box, HD STB
(Set-Top-Box) satellite receiver
Device
Using a Component Cable
Good Connection
Component connection (up to 720p/1080i)
DVD, Blu-ray player, cable box,
STB satellite receiver, VCR,
Device
Use one of the connections below to connect your TV to an external A/V device. We recommend using
HDMI for the highest picture quality.
✎
When connecting to
AV IN
on the back of your TV, attach the video cable (yellow) to the green jack
next to the
AV IN
label. The jack will not match the color of the video cable (yellow).
U
Move
E
Enter
Select Language of the OSD.
Language
:
Plug & Play
English
Español
Français
L
Move
E
Enter
Select ‘Home Use’ when installing this TV in your home.
Store Demo
Home Use
Plug & Play
U
Move
E
Enter
m
Skip
Select the Antenna source to memorize.
Air
Cable
Auto
Start
Start
Start
Plug & Play
U
Move
E
Enter
m
Skip
Set the Clock Mode.
Clock Mode
Auto
Manual
Plug & Play
U
Move
E
Enter
m
Skip
Set to daylight saving time.
DST
Off
On
Auto
Plug & Play
48%
E
Enter
m
Skip
Auto Program in Progress.
DTV Air : --
Air : --
DTV Cable : --
Cable : --
Cable : 35
Stop
Plug & Play
BN68-03115A-01
Lowest Quality Connection
Using an Audio/Video Cable
Audio/Video connection (480i only)
DVD, Blu-ray player, cable box, STB satellite
receiver, VCR
Device
VHF/UHF Antenna
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
• Cable or Satellite box
Ant or Cable Out
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Use a 75 ohm (round) cable.
or
Antenna Cable
(Not Supplied)
HDMI Cable (Not Supplied)
HDMI to DVI Cable
(Not Supplied)
Audio Cable (Not Supplied)
Audio Cable
(Not Supplied)
Component Cable
(Not Supplied)
Video Cable
(Not Supplied)
AUDIO IN
OPTICAL
Analog Audio connection
Digital Audio connection
Amplifier / DVD home theater
Digital Audio System
Using an Audio Cable
Using an Optical Cable
Optical Cable (Not Supplied)
Audio Cable (Not Supplied)
DVI OUT
AUDIO OUT
AUDIO OUT
PC OUT
HD connection
Using an HDMI to DVI Cable
Using a D-Sub Cable
HDMI to DVI Cable (Not Supplied)
D-Sub Cable (Not Supplied)
Audio Cable (Not Supplied)
Audio Cable (Not Supplied)
[QSG-490]BN68-03115A-01Eng.indd 1
2010-09-03 오후 5:42:39
