English - 3
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1.
Press the
TOOLS
button. Press the
ENTER
E
button to select
(HDMI-CEC)
.
.
Press the ▲ or ▼ button to select
Receiver
. Press the ◄ or ► button to select
On
or
Off
.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the Optical IN jack of the
receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the
TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1
channel sound to the Home theater receiver. When the source is a digital component
such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
If there is a power interruption to the TV when the
Receiver
is set to
On
(by disconnecting the power cord or a power failure), the
Speaker Select
may be set to
External Speaker
when you turn the TV on again. (see page 24)
Troubleshooting for
Symptom
Solution
does not work.
Check if the device is an device. The system supports devices only.
Connect only one receiver (home theater).
Check if the device power cord is properly connected.
Check the device’s Video/Audio/HDMI 1.3 cable connections.
Check whether
(HDMI-CEC)
is set to
On
in the setup menu.
Check whether the TV remote control is in TV mode.
Check whether it is Anynet
+
exclusive remote control.
doesn’t work in certain situations. (Searching channels, Plug & Play, etc.)
When connecting or removing the HDMI 1.3 cable, please make sure to search devices again
or turn your TV off and on again.
Check if the Function of device is set on.
•
•
•
•
•
•
•
•
•
•
I want to start .
Check if the device is properly connected to the TV and check if the
(HDMI-CEC)
is set to
On
in the Setup menu.
Press the
TV
button on the TV remote control to switch to TV. Then press the
TOOLS
button
to show the menu and select a menu you want.
•
•
I want to exit .
Select View TV in the menu.
Press the
SOURCE
button on the TV remote control and select a device other than
devices.
(Note that the channel button operates only when a tuner-embedded device is not
connected.)
•
•
•
The message Connecting to
device...
appears on the screen.
You cannot use the remote control when you are configuring Anynet
+ or switching to a view
mode.
Use the remote control when the setting or switching to view mode is complete.
•
•
The device does not
play.
You cannot use the play function when
Plug & Play
is in progress.
•
The connected device is not
displayed.
Check whether or not the device supports functions.
Check whether or not the HDMI 1.3 cable is properly connected.
Check whether
(HDMI-CEC)
is set to
On
in the setup menu.
Search devices again.
You can connect an device using the HDMI 1.3 cable only. Some HDMI cables may
not support functions.
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power
cord or a power failure, please repeat the device scan.
•
•
•
•
•
•
The TV programme cannot be
recorded.
Check whether the antenna jack on the recording device is properly connected.
•
The TV sound is not output
through the receiver.
Connect the optical cable between TV and the receiver.
•
N
N
N
N
View TV
Device List
Record
:
DVDR
DVDR MENU
DVDR INFO
Receiver
◄
On
►
Setup
U
Move
L
Adjust
R
Return
BN68-01936D-Eng.indb 32
2009-02-25 오후 8:43:54
