Samsung RF22NP Series Installation Manual Download

Page: 21 / 22

English

Installation

Connect the water supply line to the refrigerator

There are several items you must purchase to complete this connection. You may find
these items sold as a kit at your local hardware store.

Copper Tubing

•

” copper tubing

•

” compression nut (1 pc)

• Ferrule (2 pc)

Plastic Tubing

•

” plastic tubing



Molded end (Bulb)

•

” compression nut (1pc)

Refrigerator

Household water supply line

Water Line: Must be kept straight.

Compression Nut (

”) (Assembled)

Ferrule (Not supplied)

Copper tubing (Not supplied)

Plastic Tubing (Assembled)

Compression Fitting (Assembled)

Molded end (Bulb)

Compression nut (B) (

”) (Not

supplied)

Plastic Tubing (A) (Not supplied)

NOTE

If you have to relocate the refrigerator
after connecting the

water line (C)

, make

sure the joined section of the water line is
straight.

Connect the household water line to the assembled compression fitting.

- If you are using copper tubing, slip the

compression nut (B)

(not supplied) and

ferrule

(not supplied) on the copper tubing (not supplied) as shown.

- If you are using plastic tubing (A), insert the molded end (Bulb) of the plastic tubing

(A) into the compression fitting.

Untitled-3 33

2018-04-10 12:31:29

Summary of Contents for RF22NP Series























Search results

Summary of Contents for RF22NP Series

Reviews:

Related manuals for RF22NP Series

Brands by name

Popular brands

Samsung RF22NP Series, Installation Manual

Search results

Summary of Contents for RF22NP Series

Reviews:

Related manuals for RF22NP Series

Brands by name

Popular brands