background image

English - 26

( 7 ) Water

Touch this button to dispense water. 
This mode can not be used with the Ice 
Type mode simultaneously. 
Water mode shuts off when you touch the 
Cubed / Crushed Ice button.

To save electricity, the Panel Display turns off 
automatically under the following conditions: 
When no button has been pressed, when no 
doors are open, or when no Dispenser Lever 
has been pushed. 
However, the icon indicating your cubed or 
crushed ice selection, will stay on. 
When you press a button, open a door, or push 
a Dispenser Lever, the Panel Display will turn 
on again. 
Except for the Energy Saver, Water, and Cubed 
/ Crushed Ice buttons, all function buttons 
will become operational after you remove 
your finger from the button you are currently 
pressing.

( 8 ) Filter

Water filter usage

This icon lights up when you need 
to change the filter, usually after the 
refrigerator has dispensed about 300 
gallons of water (after about 6 months). 
The icon will blink red for several seconds 
when you open or close the door. 
After you install the new water filter, reset 
the filter indicator by touching and holding 
the Hold 3sec for Filter Reset button for 
3 seconds.

 

- If water is not dispensing or 

dispensing slowly, you need to replace 
the water filter because the water filter 
is clogged.

 

- Some areas have large amounts of 

lime in their water, which causes the 
water filter to clog more quickly.

( 9 ) Ice Type

Touch this button to select your desired 
ice type. 
Cubed and crushed ice modes alternate 
when you press the button. 
This mode can not be used with the 
Water mode simultaneously.

(10) Ice Maker Off / 

Control Lock (3 sec)

The Ice Maker Off button serves two 
purposes:

 

- To turn the Ice maker on and off

 

- To turn the Control Lock Function on 

and off.

1.  Ice Off Function
If you don’t want to make more ice, press 
the Ice Maker Off button.

2.  Control Lock Function
Touch and hold this button for 3 seconds 
to lock the display and the dispenser 
buttons so the buttons can not be used. 
When Control Lock is on, the refrigerator 
does not dispense ice or water, even if 
the Dispenser Lever is pressed. 
The Control Lock icon lights up to 
indicate you’ve activated the Control Lock 
function. Press 3 seconds to unlock.

Cooling Off Mode

Cooling Off mode (also called Shop 
mode), is designed for use by retailers 
when they are displaying refrigerators on 
the shop floor. 
In Cooling Off mode, the refrigerator’s 
fan motor and lights work normally, but 
the compressors do not run, and the 
refrigerator and freezer do not get cold. 
To start Cooling Off mode, touch and hold 
the Freezer, Fridge and Alarm buttons for 
5 seconds during normal operation. 
The refrigerator chime sounds and the 
temperature display flashes OFF. 
To cancel Cooling Off mode, touch 
and hold the Freezer, Fridge and Alarm 
buttons again for 5 seconds.

DA68-02954H (EN)-03-���.indd   26

2018. 2. 1.   �� 3:48

Summary of Contents for RF23HCEDBSA













































Reviews: