background image

CAUTION

1

.  Do not drop objects on the product or apply strong shock to it.  

 

Keep away from a location subject to excessive vibration or magnetic interference.

2

.  Do not install in a location subject to high temperature (over 122°F), low temperature  

 

(below 14°F), or high humidity. Doing so may cause fire or electric shock.

3

.  If you want to relocate the already installed product, be sure to turn off the power  

 

and then move or reinstall it.

4

.  Remove the power plug from the outlet when then there is a lightning. 

 

Neglecting to do so may cause fire or damage to the product.

5

.  Keep out of direct sunlight and heat radiation sources. It may cause fire.

6

.  Install it in a place with good ventilation.

7

.  Avoid aiming the camera directly towards extremely bright objects such as sun,  

 

as this may damage the CCD image sensor.

8

.  Apparatus shall not be exposed to dripping or splashing and no objects filled with  

 

liquids, such as vases, shall be placed on the apparatus.

9

.  The Mains plug is used as a disconnect device and shall stay readily operable at  

 

any time.

01-SCC_B9372_EU-ENG.indd   3

2008-03-10   오후 3:57:55

Summary of Contents for SCC-B9372













Reviews: