background image

6_ safety information

safety information

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions :

This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause 
undesired operation.

CAUTION

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction manual, may cause harmful interference to 
radio communications. Operation of this equipment in a residential area is likely to cause 
harmful interference in which case the user will be required to correct the interference at 
his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian 
Interference.-Causing Equipment Regulations of ICES-003.

1)
2)

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be 
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols 
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC 
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health 
or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste 
and recycle them through your local, free battery return system.

Correct Disposal of This Product 

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories 
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their 
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, 
please separate these items from other types of waste and recycle them responsibly to promote the sustainable 
reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government 
office, for details of where and how they can take these items for environmentally safe recycling.  

Business users should contact their supplier and check the terms and conditions of the purchase contract. 
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

im

1

2

3

4

5

6

7

8

9

1

1

1

1

1

Summary of Contents for SCD-6083R




































Reviews: