background image

86

87

Cumulative call time is cleared

All the phone numbers stored
in memory are cleared.

There is no phone number
stored in memory.

While the phone is restricted,
you have tried to make an
international call beginning 00.

You have entered invalid or no
time.

All the phone numbers in redial
memory are cleared.

The memory location you chose
is empty.

The phone number is not
registered in the base station. 

There is no empty location
under which you can store
phone numbers.

While the phone is restricted, you
have tried to make a call by
memory dial.

A phone number stored in the
selected memory location is
cleared.

A phone number is already
stored in the selected memory
location. 

LCD Messages

AIR TIME IS
CLEARED

ALL MEMORIES ARE
CLEARED

ALL MEMORIES ARE
EMPTY

INT.CALL IS
RESTRICTED

INVALID TIME

LAST CALLS ARE
CLEARED

LOCATION EMPTY

MAINTENANCE
REQUIRED

MEM. (00-79) IS
FULL

MEMORY IS
RESTRICTED

MEMORY USED!
CLEAR? YES

MEMORY USED!
STORE? YES 

Miscellaneous

Miscellaneous

NAME NOT FOUND

NO LAST CALL

NO MATCH NUMBER

NO PHONE NUMBER

NO SERVICE

NO STORED NAME

PAGE RESTRICTED

PLEASE ENTER CDMA
SERVICE FOR TIME

REDIAL CALL FAILED

SEARCHING EMPTY
MEMORY

SPEC.CALL IS
RESTRICTED

TOO FEW DIGITS!

WAIT TO RESET
PHONE

The name you are trying to
recall does not exit.

There is no phone number
stored in redial memory.

The phone number you are
trying to recall does not exit.

You have pressed 

SEND

without

entering a phone number.

The phone is out of service area. 

Name is not stored with the
phone number into memory.

While the phone is restricted,
you have tried to answer call.

You have tried to check world
time while the current time is
not set. 

The call cannot be made
completely even after
automatic redialing. 

The phone is searching empty
memory.

While the phone is restricted,
you have tried to make a
special call.

Too few digits for your lock
code. 

The phone is being initialized.

Summary of Contents for SCH-370B

















































Reviews: