background image

FCC Notice and Cautions 
 

FCC Notice 
 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 
 
(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation. 
 
This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged 
to try to correct the interference by one or more of the following measures: 
 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- Connect the equipment into an outlet on a circuit from that to which the 

receiver is connected. 

- Consult the dealer or an experienced radio/TV technician for help. 
 
The equipment may cause TV or radio interference if used in close proximity to 
receiving equipment. The FCC can require you to stop using the equipment if such 
interference cannot be eliminated. Vehicles using petroleum gas (such as 
propane or butane) must comply with the National Fire Protection Standard 
(NFPA-58). For a copy of this standard, contact the National Fire Protection 
Association, One Battery march Park, Quincy, MA 02269, Attn: Publication Sales 
Division. 
 
Cautions 
Changes or modifications made in the radio device, not expressly approved by Samsung, 
will void the user’s authority to operate the equipment. 
   
The use of any unauthorized accessories may be dangerous and void the device warranty if 
said accessories cause damage or a defect to the device. Although your device is quite 
sturdy, it is a complex piece of equipment and can be broken. Avoid dropping, hitting, 
bending or sitting on it. 

Summary of Contents for SCH-LC11R













Reviews: