SCO-1020R
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
◾
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
• The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
◾
The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
◾
The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC 12V±10%).
Troubleshooting
Specification
Specification
※
The specification for this product may change without prior notice for product improvement.
1.
Select a position where you want to install the camera.
`
2.
the wall or ceiling.
3.
J
`
Make sure the selected position can sustain the weight of the camera.
Use the screw bolts (M4 X L15) to mount the camera
Place the camera on the selected position and fit the
hole either on the top or the bottom of the camera into
the fixing bolt of the bracket, and turn the camera
clockwise.
bracket onto
You should be careful when installing the camera
because the cable connectors may be wet with
or pile up with impurities.
Camera Bracket
•
The camera bracket can be used to install the camera on the wall, ceiling or shelf.
Name
Description
Installation
Wall or Ceiling
Dimensions
57(W) x 47.2(H) x 100.5(L) mm/
2.25(W) x 1.86(H) x 3.95(L) inch
Weight
130g (0.29 lbs)
Operating Temperature
-10˚C ~ 55˚C (14˚F ~ 131˚F)
Accessories
SCREW (M4 X L15) : 3 pcs
Camera Bracket Specification
Adjusting the Camera Bracket
3.
Adjust the camera to target the video location and tighten the camera
bracket handle on the camera bracket. Install the camera on to the
male screw of the camera bracket by rotating the camera clockwise.
4.
Loosen the handle by turning it counter clockwise and then adjust the
camera position. Tighten the handle, turning it clockwise to lock the
camera in position.
5.
Connect the camera cable to the camera.
Handle
1.
Choose an installation site that can sufficiently support the weight of
the equipments to be installed.
2.
Attach the camera bracket to the wall using the supplied screws
(M4 X L15). 4x15 sized screws wall or ceiling.
Connecting to Power
• Connect the adapter to the power input connector as shown in the figure below.
(The Adapter is not provided with the Camera.)
Use a DC 12V.
Adapter (not provided)
Power Input Connector
SCO-1020R
Resistance of copper wire [at 20Cº(68ºF)]
• As the voltage drop according to the length of the cable in the above table, a camera may malfunction if
there is an excessively long cable run.
* Voltage for camera operation: DC 12V±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Copper wire size (AWG)
#24(0.22mm
2
) #22(0.33mm
2
)
#20(0.52mm
2
)
#18(0.83mm
2
)
Resistance (
Ω
/ m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Connection to Monitor
• As a connecting method varies according to instruments, refer to the manual supplied with the instrument.
• Connect the cable after power is turned off.
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
Monitor
BNC
Item
Imaging Device
1/4” CMOS
Total Pixels
680(H) x 512(V)
680(H) x 512(V)
Effective Pixels
720(H) x 480(V)
720(H) x 576(V)
Scanning System
2:1 Interlace
Synchronization
Internal
Frequency
Horizontal Resolution
520 TV lines
Min. Illumination
0 LUX ( IR LED On)
S/N Ratio
46dB (AGC off, Weight on)
Video Output
CVBS : 1.0Vp-p, 75
Ω
composite
Lens Type
Focal Length (Zoom Ratio)
3.6mm
Max. Aperture Ratio
2
Angular Field of View
H : 56° / V : 42°
Min. Object Distance
0.2m
Lens Type
Fixed
Operational
H : 15.734KHz V:59.94Hz
H: 15.625KHz V: 50.00Hz
SCO-1020RN
SCO-1020RP
Auto
Day & Night
Auto
Auto
Digital Noise Reduction
Gain Control
Video
Item
SCO-1020RN
Operational
Shutter Mode
Auto (Rolling Shutter)
IR Distance
15m (IR LED 20 EA)
White Balance
Auto (3,200K° ~ 6,500K°)
Environmental
Operating Temperature
/ Humidity
-10°C ~ +55°C (+14°F ~ +131°F) / 0% ~ 90% RH
Electrical
Input Voltage/Current
12V DC
Power Consumption
2.6W
Mechanical
Color / Material
White / ADC 12
Dimension (WxHxD)
W65.5 x H65.5 x D94.6 (2.58 x 2.58 x 3.72 inch)
Weight
325g
12
Weatherproof IR Camera
User Manual
13
Weatherproof IR Camera
User Manual
14
Weatherproof IR Camera
User Manual
15
Weatherproof IR Camera
User Manual
8
Weatherproof IR Camera
User Manual
9
Weatherproof IR Camera
User Manual
10
Weatherproof IR Camera
User Manual
11
Weatherproof IR Camera
User Manual
SCO-1020RP
outdoors
moisture
M4 X L15 sized
screws
wall or ceiling
Dimension
94.6
83.0
65.5
Unit : mm(Inches)
