Samsung SCR-3000N User Manual Download

Page: 184 / 261

4-16

4-15

DIGITAL VIDEO RECORDER

The following illustrates the intial setting of the SYSTEM SETUP menu.

①

PASSWORD

Set the system password. You can enter a 4-digit number and the initial set value is 0000.

②

PASSWORD LOCK

If you set this to ON, the system will ask for a password, which was set in PASSWORD,

when your press the MENU ( ) button or when you attempt to cancel the recording lock

while recording or when you attempt to remove the video tape from the video deck. If the

password is invalid, you will not be able to finish the desired operation. If you set this to

OFF, the system will not ask for a password for any of the operations above.[ON/OFF]

➂

HDD ERASE

If you set to ON and exit the menu, the system will delete all data stored on the HDD.
[ON/OFF]

➃

FACTORY RESET

If you set to ON and finish the menu, all settings will be restored to their factory default set-
tings. However, the data on the HDD will not be deleted. After RESET The message, “DO
YOU REBOOT SYSTEM?” will be displayed. Select YES to reboot the system. [ON/OFF]

➄

MENU SCREEN

If this is set to DARK GRAY, the background of the screen becomes darker when the
MENU button is pressed and you will not be able to see the characters clearly. If set to OFF,
you can see the current video clearly even when the MENU button is pressed.
[DARK GRAY/OFF]

➅

LANGUAGE

SCR-3000N/SSC-Dual models only supports English. SCR-3000P models however supports

German, French, Spanish, and Italian in addition to English.

There is a language support setting function for the convenience of international users. The

default language is set to English.

●

SCR-3000N/SSC-Dual [ENGLISH]

●

SCR-3000P [ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO]

➆

IR REMOCON

If IR REMOCON to ON, signals from the remote control will be received and if it is set to
OFF, signals from the remote control will not be received. The option will be turned off by
factory default reset. For instructions on how to use the remote control, please refer to “4.
Introduction to the Remote Control” on page 1-7. [ON/OFF]

⑧

MULTIPLEXER

If MULTIPLEXER is set to WITHOUT, ID Detection will not be performed and the system
will recognize it as 1CH regardless. If MULTIPLEXER is set to WITH, the Video ID input
from the Multiplexer will be detected. Set MULTIPLEXER to WITH, and exit the MAIN
MENU (DVR) to automatically start the Multiplexer ID Detection. In addition, MULTI-
PLEXER SELECT will be enabled and MOTION DETECTION-related functions will be
disabled.
[WITHOUT/WITH]

⑨

MULTIPLEXER SELECT

If MULTIPLEXER is set to WITH, MULTIPLEXER SELECT will be enabled.
The settings of all recording modes will be dependent on the Multiplexer setting.
The corresponding Multiplexers are SAMSUNG SDM-160(SDM-090), SMO-150(SMO-
210, SOM-080).

●

SCR-3000N/SSC-Dual [SAMSUNG SDM-160 / SAMSUNG SMO-150]

●

SCR-3000P [SDM-160P / SAMSUNG VPP]

Caution

Verify once again that is is OK to delete the data, as deleted data cannot be restored.

Caution

Do not set the multiplexer option to [With] and fail to receive the multiplexer output
signal as input to avoid error in recording. Please set the multiplexer option to
[Without] whenile not receiving the multiplexer output signal as input.
Set the multiplexer option to [Without] unlessif the multiplexer manufacturer of the
multiplexer is not Samsung.

System Setup

SYSTEM SETUP

PASSWORD

****

PASSWORD LOCK

OFF

HDD ERASE

OFF

FACTORY RESET

OFF

MENU SCREEN

DARK GRAY