CHANGING THE DEFAULT COPY SETTINGS
The copy options, including darkness, original type, copy size, and number
of copies, can be set to those most frequently used. When you copy a
document, the default settings are used unless they have been changed by
using the corresponding buttons on the control panel.
1.
Press
Copy
.
2.
Press
Menu
until
Copy Setup
appears on the bottom line of the display
and press
OK
.
3.
Press
OK
when
Change Default
appears.
4.
Press the left/right arrow until the setup option you want appears and
press
OK
.
5.
Press the left/right arrow until the setting you want appears and press
OK
.
6.
Repeat steps 4 through 5, as needed.
7.
Press
Stop/Clear
to return to ready mode.
ID CARD COPYING
Your machine can print 2-sided originals on one sheet of A4-, Letter-, Legal-
, Folio-, Oficio-, Executive-, B5-, A5-, or A6-sized paper.
When you copy using this feature, the machine prints one side of the
original on the upper half of the paper and the other side on the lower half
without reducing the size of the original. This feature is helpful for copying a
small-sized item, such as a name card.
This copy feature is available only when you place originals on the scanner
glass. Unload the paper in ADF.
1.
Press
ID Copy
.
2.
Place the front side of an original facing down on the scanner glass
where arrows indicate as shown, and close the scanner lid.
3. Place Front Side and Press[Start]
appears on the display.
4.
Press
Start
.
Your machine begins scanning the front side and shows
Place Back
Side and Press[Start]
5.
Turn the original over and place it on the scanner glass, where arrows
indicate as shown. Then, close the scanner lid.
6.
Press
Start
to begin copying.
USING SPECIAL COPY FEATURES
You can use the following copy features:
Collation
You can set the machine to sort the copy job. For example, if you make 2
copies of a 3 page original, one complete 3 page document will print
followed by a second complete document.
1.
Press
Copy
.
2.
Load originals face up into the ADF, or place a single
original face down on the scanner glass.
For details about loading an original, see page 28.
3.
Enter the number of copies using the number keypad.
4.
Press
Menu
until
Copy Setup
appears on the bottom
line of the display and press
OK
.
5.
Press
OK
when
Change Default
appears.
6.
Press the left/right arrow until
Copy Collation
appears
and press
OK
.
7.
Press the left/right arrow to select
On
.
8.
Press
Start
to begin copying.
One complete document will print followed by the second complete
document.
2-up or 4-up copying
Your machine can print 2 or 4 original images reduced to
fit onto one sheet of paper.
1.
Press
Copy
.
2.
Load originals face up into the ADF, or place a single
original face down on the scanner glass.
For details about loading an original, see page 28.
3.
Press
Menu
until
Copy Feature
appears on the
bottom line of the display and press
OK
.
4.
Press the left/right arrow until
Layout
appears and
press
OK
.
5.
Press the left/right arrow until
2-Up
or
4-Up
appears
and press
OK
.
While you are setting copy options, pressing
Stop/Clear
cancels the
changed settings and restores the defaults.
If you press
Stop/Clear
or if no buttons are pressed for
approximately 30 seconds, the machine cancels the copy job and
returns to ready mode.
If the original is larger than the printable area, some portions may not
be printed.
If you press
Stop/Clear
or if no buttons are pressed for approximately
30 seconds, the machine cancels the copy job and returns to ready
mode.
1
2
3
1
2
1
2
3
4