SHP-DH525
64&3."/6"-
www.samsungsds-nss.com/en
Convenient Opening
User friendly access with cards and password
Welcome Function
When a user gets close to the door lock,
the authorization standby mode will
automatically activate.
Silent-Mode Function
When going in or out, the sound of the
key entering and door opening will be
suspended.
Security Assurance Function
When someone is inside the house,
authorization for entry from the outside
will be prohibited.
Built-in Fire Detection
Generates alarm in case of a fire
Security Function
Prevents intrusion from the outside
Smartphone Interworking function
G
Conveniently open the door through the Bluetooth
function of a smart phone
Warning
2
3
4
5
6
Key Tag (
2EA)
User Manual, Product Warranty
‘AA’ Batteries (LR
6)
Emergency Key
Handle Shaft Spring
Handle Shaft, Installation Screws
Installation Manual
BIOMETRICS
CARD
BIOMETRICS
CARD
BIOMETRICS
CARD
BIOMETRICS
CARD
BIOMETRICS
CARD
When purchased, the product is set to Multi-leveled Security Code Entry Mode
initially. Please refer to “Multi-leveled Security Code Entry Mode setting” for Com-
mon Mode setting.
※
Silent Mode
Before entering the password, press the [
] button and enter the password, then both
the sound of the key entering and the door opening will be suspended. It is a useful
function if you do not want to disturb neighbors when you go in and out at night.
Safety Cautions
This section contains important information to ensure the user’s safety
and prevent potential damage to property. Please, read this section
carefully and use the product accordingly.
• The user shall not install or repair the
product without authorization.
• Do not install the product in the place
where the gap between the door and the
frame is 5mm or more.
• Make sure that no unauthorized person
has the access to the password.
• Do not operate the product with wet
hands, and keep liquids such as water
or drinks away from the product, or the
product may malfunction or be damaged.
• Do not use the excessive force or sharp
objects to push the lockbuttons, as this
can damage the product.
• Make sure that the door is completely
closed when going outside. The
manufacturer does not assume the
responsibility for any harm caused by
engagement of the lock on an improperly
closed door.
• Please do not hang on the product or pull it.
• Long-term exposure to direct sunlight
may cause a crack on its touch pad.
Avoid exposure to direct sunlight during
installation.
• During battery replacement, use a new one
instead of the existing battery.
• Be sure to correctly match the poles (+/-)
when installing the batteries. Install the
batteries with the correct poles (+/-).
• Do not use water, benzene or alcohol when
cleaning the product, as these fluids can
cause product malfunction.
• Replace the batteries within 1 week after
the battery replacement alarm sounds.
• Interference in wireless communication may
occur when this product is used.
• According to the wireless communication
environment, its battery may consume
much.
Product Components
The product components used may vary depending on the installation
environment.
Outer Body Parts
Number Pad
Unlighted
Touch Number Pad
Number Pad Lighted
Proximity Sensor
Number Pad
Away Security
Setup
Emergency Alert
Light
Double Lock Light
External Power
Contact Part
Reset Switch
Entry Complete/
Silent Mode
Switch Button
Battery
Replacement
Time Alert
Inner Body Parts
Sound Control Switch
Built-in Wireless
Module (Optional)
Auto/Manual
Locking Switch
Manual Open and
close Lever
Battery Cover
Registration
Button
Inner Body
Handle
CLOSE Button
Mortise
Opening the Door from Outside with a Password
1. Multi-leveled Security Code Entry Mode
2. Common Mode
Touching [Number
Pad] will light up
the number pad.
Touching [Number
Pad] will light up
the number pad.
When two arbitrary but-
tons are lighted, press
the buttons in order.
When the numbers on the number
pad are lighted, enter the password
and press the [
] button.
Enter the password when the
number pad is lighted, and press the
[
] button.
Success:
DING DONG DENG DONG
Fail:
DING DONG DING DONG
Success:
DING DONG DENG DONG
Fail:
DING DONG DING DONG
Note
●
Password must be entered after the light is on, and if does not, touch
[Number Pad] and re-enter.
●
To cancel, press [ ] button and re-enter.
●
If the password is wrong 5 times, “peep” warning alarm will sound 20 times
and the system will shut-down for about 3 minutes. When malfunction
happens, “beep” will sound every 10 seconds, and stop mode will be
turned off automatically after 3 minutes with multiple ‘beeps’.
Opening the Door from Outside with a Card or Key Tag
The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.
Placing the Card or Key Tag on the Card Reader
Success:
DING DONG DENG DONG
Fail:
DING DONG DING DONG
Place the card or key tag on
the card reader.
The door will be opened after
1 second.
Opening the Door from the Inside
Automatic
Locking Setting
The door is automatically locked 1 seconds after
the door is closed.
Closing the Door from the Inside
Note
●
To check if the door is locked from the inside, press the security button briefly;
the red LED will flash if the door is locked and the blue LED will blink if the door
is unlocked.
●
For 5 seconds after the door is closed, the Bluetooth authentication mode is
not turned on even though you approach the door lock.
(Note that the Bluetooth mode is turned on when you touch the number pad.)
Card and Key Tag Registration
Up to 20 cards, including the key tag, can be registered.
(Only ISO14443 A Type is available.)
1. Pressing the [Register] Button
(from the inside)
DING DONG
Open the battery cover of the inner body
and briefly press the [Register] button.
2. Entering the Password
(from the outside)
DING DONG DENG,
DING DING
Enter the password (‘1234’ after initial-
ization) when the number pad is lighted,
and press the [
] button.
- If the security mode is changed as ‘common mode’, second step will be skipped.
When the number pad is lighted, enter
‘4560852580’ and then press the [
] button.
Press and hold the [Register] button for
5 seconds.
DING DONG
DING DING
DING DING
DING DING
Initialization (Password, Bluetooth,Card, Key Tag)
All registered data (password, Bluetooth, card, key tag) are deleted. After initial-
ization, the password is set to ‘1234’, and the registered card, key tag data are
erased. Please register a new password after initialization.
1. Pressing the [Register] Button
(from the inside)
2. Entering the Numbers for
Initialization (from the outside)
Success: DING DONG DENG
Fail: DING DONG DING
DONG
GC68-02211B ED:03
Outer Body
Inner Body
Card Reader
Outer Body
Handle
Pulling down the Door Lock Handle
Rotate the door lock handle of the inner body
downward.
DING DONG DENG
4. Checking New Password Operation
(from the outside)
DING DONG DENG
DONG
To make sure the password has been
properly registered, check the new
password and close the door.
Warning
●
Manage your password with care so that unauthorized people will not
have access to it. Regularly changing your password can reduce the
risk of it being leaked.
3. Entering a New Password
(from the outside)
DING DING DENG
Enter the new password (4 to 12 digits)
and press the [
] button.
CARD
CARD
3. Placing the Card or Key Tag on the
Card Reader (from the outside)
4. Confirming Card or Key Tag
Registration (from the outside)
DING DONG DENG
Place the card or key tag to be registered on
the card reader of the outer body. You will
know the card or key tag has been registered
when “DING DONG DENG” sounds.
Place the registered card or key tag
to the card reader on the outer body.
Warning
●
To register multiple cards or key tags, lightly place another card or key tag
to the card reader within 20 seconds after registering the previous card or
key tag.
Manual
Locking Setting
The door is locked when the [Close] button
is pressed.
Strike
box
Mortise
(SHS-AML220)
Strike
Mortise
(SHS-AML320)
Strike
Or
Deadbolt
Latch bolt
Open-door
sensor
SHS-AML320
SHS-AML220
You can delete all registered cards.
Deleting Registered Cards
Enter the current password
when the number pad is
lighted, and press [
] button.
If the number pad is lights,
enter ‘88’ and press [
]
button.
DING DONG
DING DING
1. Pressing the [Register]
Button (from the inside)
Open the battery cover of the
inner body and briefly press the
[Register] button for 3 seconds.
2. Entering the Current
Password
(from the outside)
3. Entering the number
(from the outside)
DING
DONG
DENG
DING
DONG
DENG
2. Entering the Current Password
(from the outside)
DING DONG DENG,
DING DING
Enter the current password (‘1234’ after
initialization) when the number pad is
lighted, and press the [
] button.
Password Change
The password can be 4~12 digits number. Only one password can be registered.
1. Pressing the [Register] Button
(from the inside)
DING DONG
Open the battery cover of the inner
body and briefly press the [Register]
button.
