05 MENU SETUP
menu setup _
33
Alarm Out Schedule
You can schedule the automatic output for
alarms.
The scheduling is enabled by selecting alarms,
days and time blocks. The default setting is
Event Driven. For each alarm or beep, you can
activate or deactivate alarming. In case of
Event
Driven
, the alarm can be sent only when an
event is issued.
AO >
:
It indicates
Alarm Out
. All alarms are
changed according to
Alarm1
when it pressed.
0 to 23
: Time values for horizontal row.
S to H
: Days (Sunday to Saturday) and Holiday (H).
ALL
: Press this and it changes the overall
settings in the current window to Off, On, and
Event Driven.
Off
: Sets not to issue an alarm during the
setting time.
On
: Sets to issue an alarm during the setting time.
Event Driven
: Sets to issue an alarm when an
event occurs during the setting time.
Holiday
If you press
Holiday
, a calendar window appears
for you to designate holidays. Place the cursor to
a date and press the
ENTER
button to complete
designation. (When pressing the
ENTER
button
again, the setting is cancelled.)
NETWORK
You can configure the network related settings
for network connection.
IP Settings
Connection Mode
Select a network type that is connected to the
main body of the product.
- Static IP: When the main body is connected
to the network using the static IPs.
- Dynamic IP: When the main body is
connected to the network using the dynamic
IPs supplied by DHCP.
- ADSL(PPPoE): When the main body is
connected to the ADSL network using Point-
to-Point Protocol over Ethernet (PPPoE).
Bandwidth
Select a network speed among Unlimited,
2 Mbps, 1.5 Mbps, 1 Mbps, 800 Kbps,
600 Kbps, 500 Kbps, 400 Kbps, 300 Kbps,
and 128 Kbps. If the connection is made via
ADSL, you can only select the bandwidth of
600 kbps or less.
Admin Password
It is used for connection between Smart Viewer
and this product using the Admin privilege. The
password can be input up to 8 digits. Press
the
ENTER
button and type the numbers you
want using the
NUMERIC
buttons. The default
Admin password is “
4321
.”
User Password
It is used for connection between Smart Viewer
and this product using the user privilege. The
password can be input up to 8 digits. Press
the
ENTER
button and type the numbers you
want using the
NUMERIC
buttons. The default
user password is “
4321
.”
With the user privilege, you cannot access to
both Menu Setup window in DVR and DVR
Setup screen in Smart Viewer.
CAUTION
1.
If the main body of the product is
connected to a high-speed
network like LAN, it is
recommended to set the higher
bandwidth than 1 Mbps.
2.
If the device is connected to
a network using ADSL or low
bandwidth, set the bandwidth not
to exceed 600Kbps, and set the
recording mode not to exceed CIF
(standard). Setting up to a higher
bandwidth or higher recording
mode for the network environment
supporting a low bandwidth
may cause a network overload,
therefore the connection to Smart
Viewer or image monitoring may
not operate properly.
3.
When the connection mode is set
to ADSL, the bandwidth is fixed to
300Kbps.
Cancel
OK
IP Settings
Connection Mode
Static IP
Bandwidth
2 Mbps
Admin Password
User Password
IP
192.168.001.201
Gateway
192.168.001.001
Subnet Mask
255.255.255.000
DNS
168.126.036.001
ADSL User ID
ID
Password
Cancel
OK
Alarm Out Schedule
AO
Alarm 1
Alarm 2
Alarm 3
Alarm 4
Beep
Holiday
Off
On
Event Driven
All
S
M
T
W
T
F
S
H
SHR-5162_Eng.indb 33
2007-8-2 14:47:42
