Samsung SL-M4580FX Service Manual Download

Page: 167 / 252

4. Troubleshooting

► Error Code

A3–3312

A3–3320

► Error message

Sensor Failure: #A3-3312. Turn off then on. Call for service if the problem persists

The room temperature is not suitable for this set use. Please adjust room temperature

► Symptom

Outer temperature/humidity sensor is defective.

► Troubleshooting method

1) Enter SVC mode. Execute sensor test to check its operation.

(

Diagnostics > Engine Diagnostics > Engine Test Routines > Outer Temperature

)

2) Measure the resistance value of the connector at both ends.

If the value is not in 47.5KΩ ~ 52.5KΩ (@ 25

℃

), replace the outer temperature/humidity sensor(

JC32-00005A

3) If the harness and sensor are normal, replace the main board(

JC92–02722A

4-64

Summary of Contents for SL-M4580FX






















































































































































































































































Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands

Samsung SL-M4580FX, Service Manual

Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands