Samsung SL-M4580FX Service Manual Download

Page: 140 / 252

4. Troubleshooting

4.5.5.2. Fax Diagnostics

Fax NVM Read/Write

•

Diagnostics > Fax Diagnostics Fax NVM Read/Write

Purpose

To change a configuration value for fax firmware.

Operation Procedure

When the main “NVM Read/Write” window displays, users can navigate through the list of
configuration values that display along with description.

Users can also input a code to the text box to find a configuration value directly.

After selecting one value, pressing “Edit” button will open an interface for user input.

Verification

N/A

Specification

N/A

Reference

N/A

Code

Displayed Name

Description

20-200

Pause Dial Time

Pause Time (value * 1000ms)

20-210

Dial Pulse M/B ratio

33 / 66 40 / 60

20-220

Auto Dial Start Pause Time

Pause time before auto-dialing (second)

20-300

Ring On Time

Ring On Time (ms)

20-310

Ring Off Time

Ring Off Time (ms)

20-320

Ring Detection Freq

sets the Call Indication frequency range that will be detected
by LIU

20-330

Ring On Max Time

Ring On Max Time (ms)

20-340

Ring Off Max Time

Ring Off Max Time (ms)

20-400

DTMF High-Freq Level

DTMF High-Freq. Level (dBm)

20-410

DTMF Low-Freq Level

DTMF Low-Freq. Level (dBm)

20-420

DTMF Timing

DTMF duration of on/off output ( Ms)

20-500

Dial Mode

Select Tone / Pulse

20-520

Error Rate

Adjust Error Rate ( Off / 5% / 10% / 20% )

20-530

Dial Tone Detect

detect dial tone prior to sending

20-540

Loop Current Detect

detect if loop current is present prior to sending

20-550

Busy Signal Detect

detect busy signal to allow redials

20-560

TCF Duration

Adjust TCF duration (ms)

20-800

Modem Speed

Select Modem Start Speed

20-810

Fax Transmission Level

Adjust Fax Transmission Level (dBm)

20-830

Auto Dial Timeout

Adjust Auto Dial Timeout (second)

20-920

CNG Detection Count

CNG Tone Detection check count during ANS/FAX mode.

20-930

Caller ID

This option is needed to guide Caller ID off for user
environment.

20-940

Ext. Phone

Ext. Phone Detection Enable/Disable (Default : Enable 1) If
disabled, Ext. Phone cannot be detected by the device.

4-37

Summary of Contents for SL-M4580FX






















































































































































































































































Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands

Samsung SL-M4580FX, Service Manual

Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands