Samsung SL-M4580FX Service Manual Download

Page: 220 / 252

4. Troubleshooting

4.6.7. U2-xxxx type (LSU) error code

► Error Code

U2–1111

U2–1112

U2–1113

U2–1114

► Error message

LSU Failure: #U2-1111. Please turn off then on.

LSU Failure: #U2-1112. Please turn off then on.

LSU Failure: #U2-1113. Please turn off then on.

LSU Failure: #U2-1114. Please turn off then on.

► Symptom

LSU motor does not operate or it operates abnormally. / LSU Motor ready signal is abnormal.

► Troubleshooting method

1) Turn the machine off then on. Check for the LSU motor operation sound during warm-up.

2) Print a demo page to check that the machine operates normally.

3) If the problem persists, check the following :

•

If the LSU motor makes a sound,

a) Enter SVC mode to check the LSU motor ready signal.

(

Diagnostics > Engine Diagnostics > Engine Test Routines

)

b) Select “LSU Motor1 Run Ready”. (

Diagnostics > Engine Diagnostics > Engine Test Routines >

110-0000

)

c) Press ‘Start’ button. Check that the status has changed to ‘Executing -> Low -> High’.

d) If the status has not changed, the motor ready signal is abnormal. Replace the LSU.

•

If the LSU motor does not makes a sound,

a) Turn the machine off and open the side cover. Unplug and reconnect the LSU cable. Check that the LSU

motor make a sound after turning the machine on.

b) If the LSU cable is defective, replace it. Check that the LSU motor make a sound after turning the

machine on.

c) If the problem persists, replace the LSU(

JC97-03877A

4-117

Summary of Contents for SL-M4580FX






















































































































































































































































Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands

Samsung SL-M4580FX, Service Manual

Search results

Summary of Contents for SL-M4580FX

Reviews:

Related manuals for SL-M4580FX

Brands by name

Popular brands