Samsung SL-X7600GX Service Manual Download

Page: 168 / 521

3. Disassembly and Reassembly

3.2.2.2. Development Unit (Deve Unit)

NOTE

Before replacing the development unit, update the firmware
with the latest version.

Remove the corresponding drum unit.(

Refer to 3.2.2.1.

)

Close the shutter.

Release the bracket [A] after removing 2 screws. Then
unplug the connector.

Turn the toner supply pipe at a 90 degree angle in a
clockwise direction. Then, pull it to the front.

Hold the grip point of Deve unit with hand and remove
the Deve unit.

NOTE

Do not grip the bulging part when removing the Deve
unit.

3-11

Summary of Contents for SL-X7600GX























































































































































































































































































































































































































































































































Search results

Summary of Contents for SL-X7600GX

Reviews:

Related manuals for SL-X7600GX

Brands by name

Popular brands

Samsung SL-X7600GX, Service Manual

Search results

Summary of Contents for SL-X7600GX

Reviews:

Related manuals for SL-X7600GX

Brands by name

Popular brands