Samsung SpinPoint M8 Product Manual Download

Page: 5 / 83

Spinpoint M8 Product Manual REV 2.7

8.2.14

Read FPDMA Queued (60h)...........................................................................................56

8.2.15

Read Log Extended (2Fh) ...............................................................................................57

8.2.16

Read Long (22h) .............................................................................................................57

8.2.17

Read Multiple Command (C4h, 29h:extended)...............................................................57

8.2.18

Read Native Max Address (F8h, 27h :extended) .........................................................58

8.2.19

Read Sector(s) (20h, 24h: extended)...............................................................................58

8.2.20

Read Verify Sector(s) (40h, 41h :extended) ....................................................................58

8.2.21

Recalibrate (10h) ............................................................................................................59

8.2.22

Security Disable Password (F6h) ...................................................................................59

8.2.23

Security Erase Prepare (F3h) .........................................................................................59

8.2.24

Security Erase Unit (F4h)...............................................................................................59

8.2.25

Security Freeze Lock (F5h).............................................................................................60

8.2.26

Security Set Password (F1h)...........................................................................................60

8.2.27

Security Unlock (F2h).....................................................................................................61

8.2.28

Seek (7xh) .......................................................................................................................61

8.2.29

Set Features (EFh)..........................................................................................................61

8.2.30

Set Max Address (F9h, 37h: extended) ...........................................................................63

8.2.31

Set Multiple Mode (C6h).................................................................................................63

8.2.32

Sleep (E6h) .....................................................................................................................63

8.2.33

Standby (E2h) .................................................................................................................63

8.2.34

SMART (B0h)..................................................................................................................64

8.2.34.1

Smart disable operations (D9h) .................................................................................................. 64

8.2.34.2

Smart enable/disable attribute auto-save (D2h).......................................................................... 64

8.2.34.3

Smart enable operations (D8h) ................................................................................................... 65

8.2.34.4

Smart execute off-line immediate (D4h) .................................................................................... 65

8.2.34.5

Smart read data (D0h) ................................................................................................................ 66

8.2.34.6

SMART read log sector (D5h) ................................................................................................... 71

8.2.34.7

SMART return status (DAh) ...................................................................................................... 71

8.2.34.8

SMART write log sector (D6h) .................................................................................................. 71

8.2.35

Standby (E2h) .................................................................................................................72

8.2.36

Standby Immediate (E0h)................................................................................................72

8.2.37

Write Buffer (E8h) ..........................................................................................................72

8.2.38

Write DMA (CAh, 35h:extended)....................................................................................72

8.2.39

Write FPDMA Queued (61h) ..........................................................................................72

8.2.40

Write Long (32h).............................................................................................................73

8.2.41

Write Multiple Command (C5h, 39h:extended) ..............................................................73

8.2.42

Write Sector(s) (30h,

34h:extended) ............................................................................73

CHAPTER 9

MAINTENANCE..........................................................................................................75

9.1

ENERAL

NFORMATION

.................................................................................................................75

9.2

AINTENANCE

RECAUTIONS

........................................................................................................75

9.3

ERVICE AND

EPAIR

......................................................................................................................77

Summary of Contents for SpinPoint M8




















































































Search results

Summary of Contents for SpinPoint M8

Reviews:

Related manuals for SpinPoint M8

Brands by name

Popular brands

Samsung SpinPoint M8, Product Manual

Search results

Summary of Contents for SpinPoint M8

Reviews:

Related manuals for SpinPoint M8

Brands by name

Popular brands