background image

English

 

_5

●  

over

view

operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F). 

This product may not work properly if you run right after a long period of storage at a temperature below the 

guaranteed one. 

Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at 

room temperature for a period. 

Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F). 

Likewise, the hard drive may not work at a temperature below the guaranteed one.

ethernet port

This equipment is in door use and all the communication wirings are limited to inside of the building.

Security precautions

The initial administrator ID is “

admin

” and the password should be set when logging in for the first time. 

Set password for your wireless network if you use the product with a wireless router. Being not protected with 

password or using the default wireless router password may expose your video data to potential threat. 

Please change your password every three months to safely protect personal information and to prevent the 

damage of the information theft. 

Please, take note that it’s a user’s responsibility for the security and any other problems caused by 

mismanaging a password.

Summary of Contents for SRN-473S

































































































































































































Reviews: