background image

English

 _ 3

SAFETY INFORMATION

Avoid aiming the controller directly towards extremely bright objects such as sun.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, such as vases, shall be 
placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

FCC Statement

Caution :  Any changes or modifi cations in construction of this device which are not expressly approved by the 

party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, any cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

7.

8.

9.

1)

2)

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that 
produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one 
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third 
prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for 
replacement of the obsolete outlet.

  Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the 

point where they exit from the apparatus.

  Only use attachments/accessories specifi ed by the manufacturer.

  Use only with cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with 
the apparatus.

  Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus 

combination to avoid injury from tip-over.

  Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any 

way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for SSA-R2000



















Reviews: