ENG-9
ENG-8
Plug & Auto Set Up
Tuning Your Television for the VCR
Your VCR will automatically set itself up when it is
plugged into the mains for the first time. TV stations
will be stored in memory. The process takes a few
minutes. Your VCR will then be ready for use.
1
Connect the coaxial cable as indicated on page 7.
(Connecting Your VCR to the TV Using the Coaxial
Cable)
2
Plug the VCR into the mains.
Result: A message appears.
3
Press OK button to start the auto scanning
◆
The number of stations automatically stored by
the VCR depends on the number of stations that
it has found.
◆
The process will finish after a few minutes.
4
The current time and date are displayed
automatically. Check the date and time.
if it is :
◆
Correct, Press Menu button twice to exit the
menu.
◆
Incorrect, see page 9.
➢
Auto preset can be performed by pressing
■
(STOP) on the VCR continuously for 5 seconds or
more with no tape inserted.
☛
Function for “Plug & Auto Set Up” is fixed
already. So if you want to change this fixed one,
you can change it by Presetting the Stations
Automatically in OSD “ Auto Set Up” menu. (see
page 11)
You must tune your television for the VCR only if you
are not using a Scart cable
➢
To view pictures from your VCR when a Scart
cable is used, the television must be set to the
audio/video mode (AV).
1
Switch on the television.
2
Switch on the VCR by pressing STANDBY/ON on
the front of the VCR or VCR STANDBY/ON
(STANDBY/ON) on the remote control.
3
Select a programme position on the television to be
reserved for use with your VCR.
4
Insert the video cassette in the VCR. Check that
the VCR starts reading the cassette; if not, press
❿
II
button.
5
Start a scan on your television or set the television
to UHF channel 60.
6
Fine tune the television until the pictures and sound
are obtained clearly.
7
If you cannot find the pictures and sound, or there
is interference from nearby channels, it may be
necessary to change the setting of the VCR output
channel (see Setting the VCR Output Channel on
page 10 and Problems and Solutions on page 29).
8
When the picture and sound are perfectly clear,
store this channel at the desired programme
position on the television.
Result: That programme is now reserved for use
with your VCR.
TV
TV
AV1 (EURO AV)
Connecting Your VCR to the Satellite
receiver or Other Equipment
Satellite Receiver or
other Equipment
Aerial
Aerial Connector
TV
R
L
AV1 (EURO AV)
AV2 (SATELLITE IN)
SCART
Cable
TV
1
2
SCART Cable
You can connect your VCR to a Satellite receiver or
other VCR using the SCART cable if the appropriate
outputs are available on the equipment chosen. The
following illustrations give a few examples of the
connection possibilities.
1
AV2(SATELLITE): By means of 21-pin Scart
Cable H(SV-675B/SV-671B/SV-671I Only)
Plug the SCART Cable with satellite receiver or
other equipment into the AV2(SATELLITE) socket
on the rear of the VCR.
After making this connection, select the source by
pressing the input button for the AV2 input sources.
2
By means of RF Coaxial Cable
After making this connection, you must preset the
station received through the satellite tuner.
RF output channel of the satellite receiver should
be adjusted away from channel 60, which is used
by the VCR, e.g. re-adjust to channel 65.
Your VCR contains a 24-hour clock and calendar used to:
◆
Automatically stop programme recording
◆
Preset your VCR to record a programme
automatically
You must set the date and time when:
◆
You purchase the video cassette recorder
☛
◆
The time and date are set automatically
from the broadcast signal. If the signal is
weak or ghosting occurs, the time and
date may not be set automatically. In this
case, they should be set manually.
◆
Do not forget to reset the time when you
change clocks from winter to summer
time and vice versa.
1
Press MENU on the remote control.
Result: The programming menu is displayed.
2
Press the corresponding
,
❷
or
➛
,
❿
buttons to
select the CLOCK SET option.
3
Press the OK button to select this option.
Result: The CLOCK SET menu is displayed.
4
Press
➛
or
❿
to select the hour, minutes, day,
month and year.
Result: The option selected flashes.
5
Press the
or
❷
buttons to increase or decrease
the value.
Result: The day of the week is displayed automatically.
➢
You can hold the
or
❷
buttons down to scroll
more quickly through the values.
6
On completion, press MENU twice to exit the menu.
Setting the Date and Time
❷
➛❿
OK
END:
MENU
CLOCK
THU
AUTO CLOCK : ON
12:00 1/JAN/2004
➛❿
❷
END:
MENU
PROG OPTIONS INSTALL
CLOCK BONUS LANG
CLOCK
CLOCK SET
02119G SV-675B/XEU-eng 12/12/03 6:09 PM Page 8
