ENG-28
ENG-28
Audio Dubbing a Pre-recorded
Cassette
★
(SV-677I Only)
With the Audio Dubbing function, you erase the
previously recorded sound and replace it with a new
soundtrack from:
◆
A CD player
◆
A microphone connected to a sound system
◆
A cassette player
Restriction:
Audio dubbing is applicable only to the longitudinal
audio track (normal audio).
1
Connect an RCA audio cable to the appropriate
output on your sound system (CD/cassette player
for example).
2
Connect the other end of the RCA audio cable to
the audio input connectors (L, R) on the front of
your VCR.
3
Insert the pre-recorded cassette on which the audio
track is to be replaced, and press the
❿
ll
to start
playback.
4
Find the scene that you want to over-dub and press
❿
ll
on the remote control.
5
Press DUB.
Result: Your VCR is now in the Audio dubbing
Pause mode.
6
On the sound system, locate the point on the CD or
cassette at which you wish to start playback.
Example: The track that you wish to record on the
cassette.
7
When you are ready:
◆
Start playback on the sound system
◆
Press REC on the remote control.
Result: The soundtrack is replaced on the pre-
recorded cassette.
➢
The new sound will be recorded on the normal
sound track of the tape, and the original sound will
remain on the Hi-Fi sound track.
To hear the new sound and original sound mixed
together, press the Audio button on the remote
control until the MIX option is displayed (see page
22).
Using the TV Buttons on the Remote
Control
★
(SV-677I/SV-476I Only)
Your VCR remote control will work with Samsung
televisions and compatible brands.
To determine whether your television is compatible,
follow the instructions below.
1
Switch your television on.
2
Point the remote control towards the television.
3
Hold down the TV button and enter the two-figure
code corresponding to the brand of your television,
by pressing the appropriate numeric buttons.
Brand
Codes
Brand
Codes
SAMSUNG 01 to 06
PHILIPS
02, 20, 22
AKAI
09, 23
SABA
13, 14, 22 to 24
GRUNDIG 09, 17, 21
SONY
15, 16
LOEWE
02
THOMSON 13, 14, 24
PANASONIC 08, 23 to 27
TOSHIBA
07, 16 to 19, 21
Result: If your television is compatible with the
remote control, it is switched off. It is now
programmed to operate with the remote
control.
➢
If several codes are indicated for your
television brand, try each one in turn until you
find one that works.
☛
When you change the batteries in the remote
control, you must reprogramme the code,
following the same procedure.
You can then control the television using the following
buttons.
Button
Function
TV STANDBY/ON
Used to switch the television on
and off.
TV or VCR
Used to switch between th TV
and VCR modes. Only the VOL
(+ or –) and TV STANDBY/ON
buttons are operational in VCR
mode. -/-- Used to enter a two-
figure programme number.
Example: For programme 12,
press -/-- followed by
numeric buttons 1 and 2.
INPUT
Used to select an external
source.
VOL + or –
Used to adjust the volume of
the television.
PROG/TRK
Used to select the required
(
or
❷
)
programme.
DISP./
Used to switch between an
external source and the television
➢
The various functions will not necessarily work on
all televisions. If you encounter problems, operate
the television directly.
02132A SV-677I/XFA-eng 3/4/04 1:52 PM Page 28
