background image

4

INSTALLATION & MAINTENANCE

ENVIRONMENT

Leave some space

Maintain at least 10cm between the washer and
the wall.

Place the washer on a sturdy flat
surface.

If the washer is placed on an uneven or weak
surface, noise or vibration occurs. (Allowable
slope is 1 degree)

Never install the washer in a very
steamy environment or where it might
be open to the rain.

Excessive moisture may cause an electrical
shock hazard.

Avoid direct sunlight or heaters.

As plastic and electrical components are affected
by direct heat,never place the washer near
furnaces, boilers,etc. Do not place under direct
sunlight.

IN  CASE OF PUMP-DRAINED WASHER 

• Be sure to join tightly the

drain hose into the drain-
outlet on the back of the
machine.

• Install the drain hose in

the position of about
70~80 cm above the
ground.

a

b

c

c

1. Remove the adaptor from the

water supply hose.

2. First,using a "+" type screw

driver, loosen the four screws
on the adaptor. Next,take the
adaptor and turn part(b)
following the arrow  for gap
about 5mm between them.

3. Connect adaptor to the water

tap by tightening the screws
firmly.
Then,turn part (b) following the
arrow and put (a) and (b)
together.

5. Connect the other end of the

water supply hose to the inlet
water valve at the top of the
washer.
Screw the hose clockwise all
the way in.

6. If the water tap is a screw

type,assemble a water supply
hose that fits to the tap as
shown.

4. Connect the water supply hose

to the adaptor. Pull down the
part (c) of the water supply
hose. When you release part (c)
the hose is automatically
connects to the adaptor making
a 'click' sound.

HOW TO CONNECT WATER SUPPLY HOSE

Check the type of tap fitting which is in your laundry and then see appropriate instruction below:

A tap of ordinary type is desirable

In case of square tap

Take out the internal part of the connector 
and join it in the following way.

ORDINARY TAP            SQUARE TAP                 ROTATING TAP

Internal part

Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not

be used.

Summary of Contents for SW80ASP











Reviews: