Samsung Ubigate iBG2016 Configuration Manual Download | Manualshive

Page: 244 / 744

background image

CHAPTER 10. QoS

208

© SAMSUNG Electronics Co., Ltd.

Minth is given a default value of N packets, where N corresponds to ¼ of
maximum of(3 * Ts) msec of buffering(at 100 byte packets) at a rate of
interface bandwidth or 20.(For larger packets, this will result in larger amount
of buffering). This means that, if a interface is receiving not more than it’s
bandwidth, on an average at least ¼xTs msec of traffic will be buffered before
RED starts dropping. Note that these buffering requirements are calculated for
100 byte packets which are conservative. The average internet packet size is
probably between 100-200 bytes, for which the buffering would be up to twice
the amount mentioned above. The minimum permissible value for minth is L,
where L corresponds to ¼xTs msec of buffering(for 100 byte packets) at rate
of interface bandwidth or L = 5, whichever is lower.

Maxth is given a default value of N packets, where N corresponds to ¾ of
maximum of(3 * Ts) msec of buffering(at 100 byte packets) at a rate of
interface bandwidth or 20. However it is recommended to set maxth to at least
2 times the minth. Too small a difference between minth and maxth will reduce
the effectiveness of RED by causing frequent tail drops. The maximum permissible
value for maxth is H, where H corresponds to(3*Ts) msec of buffering(for 100 byte
packets) at the rate interface bandwidth or 20, whichever is higher.

Class Queue RED parameters

The EWF and MPD parameters considerations are same as described in the
section Interface RED parameters.

The minth and maxth, are the configured minimum and maximum thresholds
respectively, represents packet queue depth levels at which RED algorithm
changes its course of action, i.e. no-drop, probabilistic-drop, and tail-drop,
depending on whether the average queue size is below minimum threshold, in
between minimum and maximum thresholds, and at or above maximum
threshold respectively.

Minth is given a default value of N packets, where N corresponds to 2xTs
msec of buffering, for 200 byte packets, at a rate of CR Kbps or Ts msec of
buffering at BR Kbps or N = 5, whichever is greater.(For larger packets, this
will result in larger amount of buffering). This means that, if a class is
receiving not more than it’s CR, on an average at least(2*Ts) msec of traffic
will be buffered before RED starts dropping. Note that these buffering
requirements are calculated for 200 byte packets which are conservative.

«
...
242
243
244
245
246
...
»

Summary of Contents for Ubigate iBG2016









































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Ubigate iBG2016

Brand: Salusfin Pages: 6

Brand: Garland Pages: 6

Brand: Netopia Pages: 38

Brand: Black Box Pages: 37

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brand: CalAmp Pages: 115

Brand: MSNswitch Pages: 2

Brand: ADTRAN Pages: 20

HiGain Line Unit HLU-388

Brand: PairGain Pages: 7

Brand: InHand Pages: 69

Routers and Switches

Brand: Allied Telesis Pages: 15

Fibe-Air IP-10G

Brand: Ceragon Pages: 71

Brand: Enterasys Pages: 2

Brand: Transition Networks Pages: 5

Brand: ADC Pages: 29

Brand: Planet Pages: 431

Brand: HeimVision Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands