Samsung VAC-7700 Series Operating Lnstructions Download | Manualshive

Page: 11 / 12

background image

10

TROUBLESHOOTING

PROBLEM

CAUSE

REMEDY

Motor does not start

No voltage

Check cable, plug and
socket.

Suction force is
gradually reduced

Filter,nozzle,suction
hose tube blocked, or
bag full.

Remove the obstruction or
replace bag.

Cord does not rewind
fully

Check that the cord is
not twisted or wound
unevenly

Pull the cord out 6~10ft &
push down the cord rewind
button

DJ68-00079M(US) 7/28/01 2:06 PM Page 11

«
...
9
10
11
12
»

Summary of Contents for VAC-7700 Series













Reviews:

No comments

Related manuals for VAC-7700 Series

Brand: Xiaomi Pages: 64

MCCG902 - CANISTER VACUUM - MULTI LANGUAGE

Brand: Panasonic Pages: 56

MCCG902 - CANISTER VACUUM - MULTI LANGUAGE

Brand: Panasonic Pages: 60

MCCG467 - CANISTER VAC - MULTI LANGUAGE

Brand: Panasonic Pages: 20

Brand: Samsung Pages: 20

Brand: Samsung Pages: 16

Brand: Parkside Pages: 84

Brand: Avanti Pages: 80

Power-Touch Handle

Brand: Eureka Pages: 12

Brand: Eureka Pages: 16

Brand: Maestro Pages: 104

Brand: Fagor Pages: 34

Brand: TCL Pages: 17

Brand: Daikin Pages: 15

Brand: Mestra Pages: 16

Brand: FXA Pages: 68

Harry HDH.201-A2

Brand: Numatic Pages: 20

Brand: Sytech Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands