background image

WSM520V

 

                                                                                                                            

 

Version 1.0 

Samsung Electronics 

page 1 of 8

 
 

 

User Manual 

 

1. Introduction 

 

The WSM520V module is wireless audio module based on AV5100. The AV5100 is 5GHz wireless audio 

SoC (System-on-chip), optimized for building point to multi-point digital wireless audio solutions such as 

wireless subwoofers, wireless rear speakers and in home theater system. The AV5100 contains all the 

necessary radio transceiver and digital baseband circuitry to form a complete digital wireless node without the 

need for external processing.  

  The WSM520V can be powered from a +5V supply input and the AV5100 contains all the necessary power 

management and analog circuitry needed to operate the chip. 

The WSM520V can operate in upper bands (5725~5825MHz) of 5GHz spectrum, enabling worldwide 

coverage. 

 

2. Feature 

 

 

Product form factor 

 

Module Size (mm): 40.0 (W) X 26.0 (L) X 3.0 (H) 

 

PCB size (mm): 40.0 (W) X 2.6.0 (L) x 1.0 (H) 

 

Shield can (mm): 24.7 (W) X 21.9 (L) X 2.0(H) 

 

Antenna Type : PCB Printed Antenna  

 

 

 

 

 

Summary of Contents for WSM520V









Reviews: