background image

4

WASHING PROCEDURE

TO WASH

1.  Before starting washing, check the following;

-  Connect the water supply hose and open the 

water tap.

-  Connect the power cord to the power supply 

outlet.

-  Lay the drain hose(A) down toward a sinkhole.

-  Place the drain hose(A) in sink or bath about 

70~80cm above the ground.

2.  Set the WASH SELECTOR 

KNOB to the desired 
mode.

3.  Set the CYCLE SELECTOR KNOB to ‘WASH·RINSE’. 

(In case no drain pump) (‘

WASH

’ in case drain pump)

4.  Set the WATER SELECTOR 

KNOB to WASH .

5.  Load laundry in the wash 

tub.

6.  Fill water in the wash tub 

and add the detergent.

7.  Set the WASH TIMER 1-15 

minutes.

8.  After washing,set the 

CYCLE SELECTOR KNOB to 
‘DRAIN’ for drain.

SPIN DRY

1.  Transfer the clothes into the spin basket and 

arrange the clothes evenly.

2.  Be sure to attach the safety cover and close the 

inner lid.

3.  Close the spin dryer lid.

4.  Set the AIR TURBO SPIN TIMER 1-10 minutes.

5. Incomplete spining. (Severe vibration or 

unbalance) See “When you load ...”on page 6.

inner lid

safety cover

(Without pump)

(With pump)

(WITHOUT PUMP)

(WITH PUMP)

70~80cm

Bottom of balancer

Safety cover

WT80J7-02206F_EN.indd   4

2006-06-17   ¿ÀÈÄ 3:59:37

Summary of Contents for WT80J7









Reviews: