background image

 

Installation and Operation Manual 

11 

1-3 Specification 

[AIS-50N] 

GENERAL 

Category 

Detail 

Size 

164 mm(H) x 183 mm(W) x 92.5 mm(D)

 

Display 

5.6” diagonal, TFT color, 480 x 640 pixels.

 

Supply voltage 

10 to 34 V DC 

Supply current 

13.8 V                                                         

24 V

 

1A    - AIS receiving by mode                  0.5A    - AIS receiving by mode 
2A    - AIS transmitting mode                  0.9A    - AIS transmitting mode 

External beeper or light 
output 

Switched to ground to sound alarm, 30V DC, 200 mA maxmum 

Operating temperature 

-10° to 50°C 

ALARMS

 

User set up

Arrival, Anchor, deviation, risk, low voltage, AIS risk vessel, AIS approaching 

GPS NAVIGATION

 

Chart card 

NAVIONICS SD Card 

User card 

SD Card 

Waypoints 

Up to 10,000, with default or user defined alphanumeric names up to 
eight characters. 

Routes 

100 Routes, with up to 100 points each 

Tracks 

By time or distance, 10 track of 15,000 points 

Chart datums 

216 Chart datums, One user-defined map shift. 

Chart scale 

0.2 to 500 nm for chart (chart dependent) down to 0.005 nm in plotter 
mode. 

COMMUNICATIONS

 

NMEA 

NMEA 0183 4800, 9600, 38400 baud, NMEA 2000 

NMEA 0183(1) Inputs from 
compatible instruments 

DBK, DBS, DBT, DPT, GGA, GLL, GNS, GGA, GSV, HDG, HDT, MDA, 
MTA, MTW, MWD, MWV, RMC, RPM, VHW, VTG, VWT, ZDA 

NMEA 0183(1) Outputs, for 
compatible instruments 

APA, APB, BWR, GGA, GLL, GSA, GSV, RMB, RMC, VTG, XTE, DBT, 
DPT, MTW, VHW, XDR   

NMEA 0183(2) Inputs from 
compatible instruments 

GGA, GLL, HDT, RMC, GSV, SSD, VSD 

NMEA 0183(2) Outputs, for 
compatible instruments 

GGA, GLL, HDT, RMC, GSV, VDM, VDO, ALR, TXT, ACS, ACA, ACK, GSB 

NMEA 2000 Inputs from 
compatible instruments 

System date and time(PGN126992),Vessel 
Heading(PGN127250),Engine parameters/Rapid Update(PGN127488), 
Engine parameters/Dynamic(PGN127489),Trip 
parameters/Engine(PGN127497),Engine 
parameters/Static(PGN127498),Fluid level(PGN127505),Water 
Speed(PGN128259),Water depth(PGN128267),Position/Rapid 
Update(PGN129025),COG & SOG/Rapid Update(PGN129026),GNSS 
Position Data(PGN129029),GNSS DOPs(PGN129539),GNSS Sats in 
View(PGN129540),Wind Data(PGN130306),Environmental Parameter-
Water temp(PGN130310),Environmental Parameter(PGN130311) 

NMEA 2000 Outputs, for 
compatible instruments 

Water Speed(128259), Water depth(128267), XTE(129283), NAV. 
data(129284), NAV. data(129285), COG & SOG(129026), GNSS 
position(129029), Water temp.(130310) 

AIS

 

VHF Transceiver 

Transmitter x 1 
Receiver x 2

 

Frequency: 156.025 to 162.025 MHz in 25 kHz steps 
Receiver 1. default CH is 87A, AIS (161.975 MHz) 
Receiver 2. default CH is 88B, AIS (162.025 MHz) 

Channel Bandwidth

 

25 kHz 

Communication 

Simplex & semi-duplex operation

   

Antenna Impedance 

50Ω(

BNC) 

Frequency  tability 

±10 PPM(-20

 to +60

 

 
 

 

Installation and Operation Manual 

12 

1-4 Packing List 

 

 

Item List 

Part number 

Display 

AIS-50N-E 

Bracket 

N560-DB 

Display Cover   

N560-CB 

Protection Cover 

N560-CC 

Power Cable 

LTW-2000-8   

Bracket mounting screw 

N560-BP 

Flush mount Kit (Including scr w) 

N560-TK 

Cable tie 

N560-CK 

User’s Manual(Eng)

 

AIS-50N-ME 

 

 

1-5 Optional Accessories 

 

Model 

Part number 

Item List 

GPS A   
GPS Antenna Installation Material 

 
SAN-60-10M 

GPS a TNC Plug 
GPS antenna support 
GPS antenna cable(10m) 

GPS Antenna Stand type 
Support 

57745 

GPS Antenna Stand type 
Support

 

VHF A   
VHF Antenna Installation Material 

 
SAN-150 

VHF a BNC Plug 
VHF antenna support 
VHF antenna cable(15m) 

 
 

 

 
 

 

Summary of Contents for AIS-50N



































Reviews: