background image

  

CAUTION

: Always turn water OFF before removing existing faucet or 

INSTALLATION INSTRUCTIONS

SINGLE HANDLE
Kitchen Faucet

For safety and easy faucet replacement, San-Ei recommends the use of 
the following helpful tools:

Keep Instructions for Future Reference

Thank you for purchasing San-Ei’s quality faucet.
With simple care and maintenance,  it will provide you with many years of reliable 
performance. 
Please read instructions before installation.

TIPS FOR REMOVAL OF OLD FAUCET

                    disassembling the faucet.
                    Open the faucet handles to relieve water pressure and ensure that 
                    complete water shut-off has been accomplished.  
                    (Complies with ASME A112.18.1) 

K 8 7 9 2 J - B W

BW-0BH

PLIERS

CHANNEL LOCKS

SAFETY GLASSES

PIPE WRENCH

ADJUSTABLE WRENCH

BASIN WRENCH

PHILLIPS SCREWDRIVER

FLASHLIGHT

- 1 -

T o o l s

A b o u t   T h i s   M a n u a l

-  8 -

Toll Free: 1(800) 222-RWVC(7982)

In the United States, please kindly call our toll free number 
for answers to any product, installation, or warranty questions.

RED-WHITE VALVE CORP.
20600 REGENCY LANE, LAKE FOREST, CA 92630 U.S.A.
Phone                :       (949) 859-1010

CONTACT

LIMITED WARRANTY

SAN-EI products have been manufactured under the highest standards of quality and workmanship, 
and warrants to the original consumer purchaser that its products are free of defects in material and 
workmanship. 
1. Ceramic cartridges and PVD finishes carry a 

limited lifetime warranty

 to the 

Original Consumer 

Purchaser

 for as long as that consumer purchaser owns his/her/their home. All other parts are warranted 

for 

2 years 

after the date of purchase.  

2. SAN-EI warrants to the 

Commercial Purchaser

 that their products, purchased for commercial, 

industrial or other business use, are free from defects of workmanship and materials for a period of 

1 year 

after the date of purchase.  

All warranties are to the original purchaser and require presentation of original sales receipt. Warranty 
is not transferable. 

During the warranty period, SAN-EI will, at its option, repair or replace any part 

or parts which have been determined to be defective if returned at purchaser’s expense. This 
shall be the sole remedy available under this warranty. Defects or damage caused by the use of 
other than genuine SAN-EI parts are not covered by this warranty. Installation or any other labor 
charges associated with the repair or re-installation of SAN-EI products is not covered by this 
warranty.

 Damage due to improper installation, misuse, poor maintenance practices, accident, alcohol, 

or other organic solvents, or use in any manner contrary to the written instructions provided, whether 
done by contractor, service company, or end user, are excluded from this warranty. Some states, 
provinces and nations do not allow the exclusion or limitation of incidental or consequential damages, 
so the above limitations or exclusions may not apply to you. This warranty gives you specific legal 
rights and you may also have other rights which vary from state to state, province to province, nation 
to nation.
SAN-EI will advise you of the procedure to follow in making warranty claims. Simply write to explain the 
defect and include product instruction manual, along with original proof of purchase receipt showing the 
store name, address and date of purchase. 
Be sure to include your name, address and telephone number.

Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed 
to stand in contact with the brass. 
The amount of lead contributed by any faucet is highest when the faucet is new.
The following steps may reduce potential exposure to lead from faucets and other parts of the 
plumbing system. 

*Always run the water for a few seconds prior to use for drinking or cooking.
*Use only cold water for drinking or cooking. 
*If you wish to flush the entire plumbing system of water that has been standing in the pipes or 
 other fittings.
 Run the cold water until the temperature of the water drops, indicating water coming from the 
 outside main. 
*If you are concerned about lead in your water, have your water tested by a certified laboratory in 
 your area. 

USER INFORMATION

Summary of Contents for K8792J-BW








Reviews: