background image

S&C IntelliCap

®

 Automatic Capacitor Control

Instruction Sheet  1022-510

© S&C Electric Company 2003-2017, all rights reserved

December 4, 2017

Installation

Table of Contents

Section Page

Section Page

Introduction

Qualified Persons     .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Read this Instruction Sheet    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Retain this Instruction Sheet    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Proper Application   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Special Warranty Provisions    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

Safety Information

Understanding Safety-Alert Messages    .  .  .  .  .  .  .  .  .  .  .  .  . 4
Following Safety Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Replacement Instructions and Labels   .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

Safety Precautions

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

Installation

Applicable Software   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Pre-Installation Checklist   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Optional In-Shop Setup   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6 
Installing the Current Sensor (var only)   .  .  .  .  .  .  .  .  .  .  .  .  . 7
Onsite Installation  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Meter Base Mounting   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10
Bracket Mounting   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14
Testing Capacitor Bank Operation   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 17
Setting the Control for Manual Operation    .  .  .  .  .  .  .  .  .  . 17

Wiring Diagrams

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 18

NOTICE

The latest instruction sheets are posted as PDF files at

 sandc.com/en/support/product-literature/

 . IntellCap software 

can be downloaded at 

sandc.com/en/support/sc-customer-portal/

 .

 

If you need assistance, please contact

 GSMC@

sandc.com 

or call (888) 762-1100 .

Summary of Contents for IntelliCap

























Reviews: