background image

2

  S&C Instruction Sheet 695-545

Introduction

Qualified Persons

  WARNING

Only Qualified Persons who are knowledgeable in the installation, operation, and 
maintenance of overhead and underground electric distribution equipment, along 
with all associated hazards, may install, operate, and maintain the equipment 
covered by this publication. A Qualified Person is someone who is trained and 
competent in:
•  The skills and techniques necessary to distinguish exposed live parts from nonlive 

parts of electrical equipment

•  The skills and techniques necessary to determine the proper approach distances 

corresponding to the voltages to which the Qualified Person will be exposed

•  The proper use of special precautionary techniques, personal protective equip-

ment, insulated and shielding materials, and insulated tools for working on or near 
exposed energized parts of electrical equipment

These instructions are intended ONLY for such Qualified Persons. They are not 
intended to be a substitute for adequate training and experience in safety proce-
dures for this type of equipment.

Read this  

Instruction Sheet

NOTICE

Thoroughly and carefully read this instruction sheet and all materials included in 
the product’s S&C Instruction Handbook before installing or operating your S&C 
Vista SD Underground Distribution Switchgear. Familiarize yourself with the Safety 
Information and Safety Precautions on pages 4 through 6. The latest version 
of this publication is available online in PDF format at 

sandc.com/en/support/

product-literature/.

Retain this  

Instruction Sheet

This instruction sheet is a permanent part of your S&C Vista SD Underground Distribution 
Switchgear. Designate a location where you can easily retrieve and refer to this publication. 

Proper Application

  WARNING

The equipment in this publication must be selected for a specific application. The 
application must be within the ratings furnished for the equipment. Ratings for the 
Vista SD Underground Distribution Switchgear are listed in the ratings table in 
Specification Bulletin 695-33. The ratings are also on the nameplate affixed to the 
product. 

Summary of Contents for Vista SD

























Reviews: