background image

   

SANDENVENDO AMERICA INC

 

1188858N ECN 56775 

 

 
 

A COMMITMENT TO SAFETY 

 
The SandenVendo is committed to safety in every aspect of our product design.  
SandenVendo is committed to alerting every user to the possible dangers involved in 
improper handling or maintenance of our equipment.  The servicing of any electrical or 
mechanical device involves potential hazards, both to those servicing the equipment 
and to users of the equipment.  These hazards can arise because of improper 
maintenance techniques.  The purpose of this manual is to alert everyone servicing 
SandenVendo equipment of potentially hazardous areas, and to provide basic safety 
guidelines for proper maintenance. 
 
This manual contains various warnings that should be read and carefully followed to 
minimize the risk of personal injury to service personnel.  This manual also contains 
service information to insure that proper methods are followed to avoid damaging the 
Hot Food Display (HFD) or making it unsafe. It is also important to understand these 
warnings are not exhaustive.  SandenVendo could not possibly know, evaluate, or 
advise of all of the conceivable ways in which service might be done, nor can 
SandenVendo predict all of the possible hazardous results.  The safety precautions 
outlined in this manual provide the basis for an effective safety program.  Use these 
precautions, along with the service manual, when installing or servicing the HFD. 
 
We strongly recommend a similar commitment to safety by every servicing organization.  
Only properly trained personnel should have access to the interior of the machine.  This 
will minimize the potential hazards that are inherent in electrical and mechanical 
devices.  SandenVendo has no control over the machine once it leaves the premises.  It 
is the owner or lessor’s responsibility to maintain the Hot Food Display in a safe 
condition.  Follow all Safety Warnings and Installation Requirements in this manual.  
Refer to the Technical Service Manual for recommended maintenance procedures.  If 
you have any questions, please contact the Technical Services Department of 
SandenVendo at 800-344-7216.  
 

FOOD FOR THE HOT FOOD DISPLAY 

 
The HFD, HFDM, and HFDH units are design to hold unwrapped, wrapped, and boxed 
food.  The HFDHC is designed to hold wrapped and boxed food.  Hot food displays are 
not designed to heat cold food - put only hot food in the hot food display.  
 
 

 

Summary of Contents for HFDM00002













Reviews: