background image

07

GB

F

E

NL

D

Presetting stations – FM / AM

The radio has 20 memory presets each for FM and AM radio.

1. 

With your radio switched on, press the Source button to select the desired waveband.

2. 

Tune to the required radio station as previously described.

3. 

 To store the FM / AM station as a preset, press the Page button to select the required preset page 1 to 4 and then 
press and hold the required preset button (1-5) until you hear a beep and the display will show the page and the 

memory pre-set you selected. e.g. “ 

 ”.

Recalling a preset station – FM / AM

1. 

With your radio switched on, press the Source button to select the desired waveband.

2. 

 To recall a preset station, press the Page button to select the required preset page (1-4) and momentarily press 
the required Preset button (1-5), your radio will tune to the station stored in the selected preset memory.  

The display will flash "---" if no station has been stored to that preset.

 

NOTE

Setting the alarm

Your radio has two types of alarms which can be set to wake you with AM / FM radio or buzzer alarm. Ensure that 

the time setting is complete before setting the alarm time. The alarms can be set while the unit is off or while playing. 

Alarms will be retained in the event of a power failure.

Setting the radio alarm

1. 

 Press and hold the radio alarm button until the radio alarm symbol 

 flashes on the display followed by two 

beeps.

2. 

 Rotate the Tuning control knob to select the desired hour and press the Select button to confirm the hour setting.

3. 

 Rotate the Tuning control knob to select the desired minute and press the Select button to confirm the minute 

setting. The radio alarm setting is now completed. The active radio alarm symbol is shown on the display. The 

radio alarm is set to the station last listened to.

The radio alarm will automatically switch to buzzer alarm when the selected radio alarm station signal is too 

weak.

 

NOTE

4. 

To quick change the On / Off status of the radio alarm, press and release the radio alarm button.

Setting the buzzer alarm

1. 

 Press and hold the buzzer alarm button until the buzzer alarm symbol 

 flashes on the display followed by 

two beeps.

2. 

 Rotate the Tuning control knob to select the desired hour and press the Select button to confirm the hour setting.

3. 

 Rotate the Tuning control knob to select the desired minute and press the Select button to confirm the minute 

setting. The buzzer alarm setting is now completed. The active buzzer alarm symbol is shown on the display.

4. 

 To quick change the On / Off status of the buzzer alarm, press and release the buzzer alarm button.

Summary of Contents for PR-D12BT













Reviews: