background image

2

AC OR BATTERY POWERED

COLUMBIA SPECIFICATIONS  

SINK WITH ELECTRONIC SENSOR

800.626.2117   

columbiasinks.com

   info@

columbiasinks.com

©2021 Columbia Products

Installation Instructions

Step 1

1. Install strainer assembly.
2.  Attach bowl to pedestal base by slipping bolts on bowl through openings on pedestal base as 

shown in illustration A.

3. Tighten the 6 nuts to the threaded bolts under bowl. Do not over-tighten.

Step 2

1. Install faucets to the sink following the instructions provided with sensor unit.
2. Attach supply tube with elbow to back of faucet.
3. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Place sink at the desired location.
2. Mark the floor where the four holes are at the pedestal base as shown in illustration B.
3. Drill holes as required for mounting hardware (Hardware not included).

Step 4

1. Secure sink to floor.
2. Connect waste line to strainer assembly.
1. Mount sensor control box at desired location on wall.
2. Connect power line from sensor to control box.
3. Attach supply tube from faucet to control box.
4. Connect hot and cold water from the source to mixing check valve.
5.  Remove aerator from the spout and flush water system. (see step 7 sensor installation 

instructions)

6. Check connections for leaks.
7. Replace aerator onto the spout.

Parts List

 (1) Sink bowl
 (1) Pedestal base
 (6) Nuts and washers to attach bowl to pedestal base
 (1) AC or battery powered sensor faucet assembly
 (1) Strainer assembly with basket 
 (1) Mixing check valve 

WARNING:

 This product can expose you to chemicals including Chromium (hexavalent compounds), 

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects 
or other reproductive harm. For more information go to 

www.P65Warnings.ca.gov

.

NOTE

Lead content originates from Brass components in valves and faucets and is certified under 

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Tools Required

 Tape measure
 Adjustable wrench
 Drill motor and drill bits
 Pipe wrench
 Level
 Safety glasses
 Screw drivers: phillips and standard
 Pencil
 Socket wrench

Go to 

columbiasinks.com

 

for more information on replacement parts and installation videos.

Illustration A

Illustration B

Summary of Contents for ES2-521L










Reviews: