background image

 

Sanosil Q-Jet Advanced

 

 

 

 

 

 

 

2.8. Important safety Directions 

(Read carefully before use) 

 
 

Caution (atomized Sanosil Disinfectant): 

 

1.

 

When the Q-Jet has completed its dispensing cycle, the room will be full of atomized Sanosil Disinfectant. The 
treated room MUST REMAIN UNOCCUPIED FOR AT LEAST 120 MINUTES AFTER FOGGING. 120  minutes is the 
minimum wait time and means not that the room is safe to re-enter or reoccupy. Length of wait time increases 
with fogging quantity (ml/m

3

). 

 

2.

 

When room re-entry is required before treatment process is completed or to perform a H

2

O

2

 level check , 

proper personal equipment (PPE) including wraparound style goggles; respirator mask (filter class ABE1) 
filtering hydrogen peroxide (for example: 3M 4277 or 3M 7500 mask with 6057 filter) and gloves should be 
worn to safely enter the room. 

 
 

Caution (Sanosil Q-JET device) 

 
A caution statement in this manual identifies a condition or practice, which if not corrected or discontinued immediately, 
could lead to serious injury or death. 
 

1. 

KEEP OUT OF REACH FOR CHILDREN. 

 

2. 

Carefully read all instructions, warning, caution and first aid statements prior to use. 

 

4. 

Use only as directed. 

 

5. 

The device is designed for easy-use. However, only properly trained individuals should use this device. 

 

6. 

Do not leave the device unattended between uses. 

 

7. 

Electric shock hazard. Do not plug in if electrical plug or parts are wet. 

 

8. 

Use only a Sanosil supplied electrical power cord. 

 

9. 

Take care to prevent water or other fluid from entering the device. Should this occur, allow to completely dry 
before use. Check the accuracy of all operating functions. 

 

10.

 

Always unplug the power cord from the outlet before moving the device. 

 

11.

 

There are no user-serviceable parts inside the device other than the nozzle. An operator may only perform 
maintenance procedures specifically described in this manual, all other repairs should be made by the 
manufacturer. 

 

12.

 

Position the device on a secure surface to prevent rolling or moving while in use. 

 

13.

 

Do not tip the device on its side at any time unless completely empty and dry. 
as this can cause leakage and damage on electrical parts 

 

14.

 

Do not overfill the tank as this can cause leakage and damage on electrical parts 

 

15.

 

Protect this device from severe impact and shock. 

 

16.

 

While in use, the body of the device may become warm to the touch. Handle with caution.  

 

17.

 

Read the specific warning and caution statements of the Sanosil disinfectant you use. 

 

18.

 

To ensure effectiveness and safety, use 

only

 

with Sanosil disinfectant. Using any other manufacturer’s disinfecting 

or cleaning product will result in serious injury, exposure and environmental damage. 

 

19.

 

Sanosil Ltd. is not responsible for any injury or damage caused by using this device outside of the specific 
parameters detailed in this manual. 

 

20.

 

Store in a safe, dry location. Do no place anything on top of the device. Store in an upright position. 

 

 

 

Summary of Contents for Q-Jet Advanced 2 Series





























Reviews: