Sanotechnik SanoSpa SPA08, Instructions For Using Manual

INSTRUCTION FOR USING THE SPA OUTDOORPOOL

53

To activate a permanent filtering without a timeout, in active mode press “         ”. Process of 
filtering begins the same as described above, but does not stop automatically.

PROGRAMMING INSTRUCTIONS

50

(1)  Press “         ”,and enter to Circulation-cleaning setting status, and “        ”of the LCD 

display, Mark of “CYCLE” is flasfed, In the same time, The Circulation-cleaning start 
time setting is oning. Press “         ”again, The Circulation-cleaning setting will quit in 
without save.

(2)  Press “        ”and “         ” can change the start working time of Circulation-cleaning: It 

will add 1 minute when pressing “         ” each time and the minutes could be added 
thecontinually when pressing the “          ” without stop. The adjustment range is 0~59. 
It will add 1 hour when pressing “       ” each time, and the hours could be added the 
continually when pressing the “          ” without stop. The adjustment range is 0~23. When 
you set up well of the start time , you could go on to the next step.

(3)  Press “           ” to continual working time setting of Circulation-cleaning, it will show the 

minimum continue time is 5 minutes on the LCD, and this time will not flash. It will add 5 
minutes by pressing “           ” each time, And add 1 hour by pressing “          ”  each time. 
please note that the maximum of continual time is 19 hours and 55 minutes. When you 
set up well of the continual time , you could go on to the next step.

(4)  When everything is setting well, Press “        ”, the system will quit the Circulation-

cleaning setting status with save.

NOTICE
1.  all setting of Circulation-cleaning must be in Waitting mode status.
2.  Circulation PUMP and OZONE are not working while all setting time.

5.  Pre-heating setting:

Only one pre-heating setting is allowed each day. The LCD can show clearly in the following 
figures about whether pre-heating setting status are ON or OFF.

Pre-heating setting is in the “

Waitting Mode

” status and the LCD display “- - -”. 

(1)  Press “       ”,and enter to Pre-heating setting status, “ON” of the LCD display, The 

“PREHEAT” mark is flashed, In the same time, The Preheat start time setting is oning. 
Press “           ” again, The Preheat setting will quit in without save.

Fig.7: Pre-heat ON

Fig.8: Pre-heat OFF

E.  HEATING / PREHEATING

You can also set this program to be active once a day or is active continuously. For the daily pre-
heating setting in passive mode press            then press            or            to set the initial heating time. 
The minimum heating time is 5 minutes and increases with each pressure of          for 10 minutes. 
Press          . Now you can set the heating time with the            or           .
The maximum preheat time is 19 hours and 50 minutes! Press           again. Now you can press
          to set the water temperature between 15 ° C and 42 ° C.
To exit this menu, press           , so your settings will not be saved. But if you press           your 
settings will be saved. When you have saved the settings, “ON” appears on the screen. If you 
pressed          , “OFF” appears on the display.

MHz/CH

SET

PREHEAT

c

MHz/CH

SET

PREHEAT

When the time you set is displayed, the circular pump is switched on and the heating is turned on. 
And it is not  important if the pool is operating in an active or passive mode. Time is counting down 
on the screen till the end of heating. Heating is switched off as soon as the desired temperature 
has been reached or when it has expired the time, set for heating. In the first 59 seconds the 
heating can not be switched off. After 1 minute you can switch off the heating by pressing          . 
To set the uninterrupted heating without turning off,  press             in active mode. Now the heating 
is switched on and is in operation together with a circular pump until the desired temperature is 
reached. You can keep the temperature on the next way:
Set the temperature to 35 ° C. When the temperature drops to 34 ° C, the heating is switched on 
together with the circular pump and heats water at 36 ° C and then switches off, etc. ...

PREHEAT

c

F.  FREEZING PROTECTION

The massage pool has built-in protection against freezing. It is activated if the water temperature 
falls below 5 ° C. Heating is switched on until 10 ° C is reached.

G.  RADIO/CD/AUX

In active mode, press            to activate the radio. The antenna is located in the control box, which 
was curled and fastened in the hinge for transportation. Develop it and install it so that you will 
have a good reception.