Sanotechnik TR20, Mounting And Using Instructions

ENGLISH – ENGLISH – ENGLISH – ENGLISH – ENGLISH    – ENGLISH - 

Introduction  

1.

Before you unpack the shower, you check the packaging for damage. Later complaints will not be recognized. Before

assembling, all parts for damage and completeness are checked. In case of problems contact the seller and us time and
you will get a satisfactory answer.

2.

For installation the following tools is required: drill, screwdriver, spirit level, tape measure, pen, ring wrench

.

3

. With embossed glass or frosted glass is to be noted is that the smooth side mounted to the inside.

4.

It is all factory-fitted shower room for testing purposes, connected, tested and packaged.

5

. Place the shower tray and using adjustable feet, so set that no water remains in the shower tray.

IMPORTANT: stress test. Subsequent complaints are excluded.

6.

The assembly should be conducted only by authoritarian specialist firms (eg plumber), otherwise it will void the

warranty. (See also note for connection of water and electricity)

7.

It is observed the enclosed assembly instructions and all parts must be additionally sealed against each other with

sanitary silicone (silicone) Leak test. In addition, need to be checked all the screws, hose clamps, etc. to its strength and
tightness. It might have come loose due to the transport something.

INSTALLATION - MAINTENANCE - WARRANTY - SECURITY - TERMS OF USE 

TECHNICAL DATA:

Conection

220 V / 50 Hz

, Control 

12 V 

Water pressure  

1 – 3 bar, max. 60° WW, max. 9° DH 

1.

Water installation:

(On site) The connection may be performed by an officially licensed installation companies. The installation 
requirements of the local water company and the provisions of DIN 1988 are to be observed strictly. For the sewer 
connection is to provide for a trap. 
Attention: No rigid pipe connections between Fertigduschen and water - risk of breakage! This line must be secured 
by a Rohrunterbrecher type A2 according to DIN 1988. The connections must be flexible, allowing an unobstructed 
maintenance or service at any time. 
The water temperature of the water, which flows through the faucets and showers can be max.    C..

°

60  The water 

pressure can be max. 4 bar. 
In general, observed for the water installation with all legal requirements

2.

WATER 

CONDUCT:  (On site) 

∅

 40mm (

∅

 50mm)

There must be a flexible, extensible intermediate (50 cm) between the siphon and sewer connection be installed so that a push
back for maintenance or service is possible.

3.

Electrical 

installation   

(On site) The electronic connection may be performed only by an officially licensed electrical company.

The installation requirements of local utility companies and the provisions of DIN 57100 or
VDE 0100 Part 701 must be strictly observed. The cable (sheathed cable H05VV-f3G2, 5 YMM-J 3x2, 5 mm ² up to 3500 watts)
must have an earth leakage circuit breaker (at least 25 A 230/400 V ~ Auslösenennstrom I = 0.03 A are held) and a circuit breaker
IN = 16 A or 25 A U-type (in Austria: IN = 13 A 16 or A C-Type will be protected). Similarly, this circuit must be switched off with an
all-pole switch with at least 3 mm contact gap. (must be in the protected area 3) are the equipotential line (at least 4 mm ² copper)
is connected to the appropriate agencies. Schematic is attached.

4.

Appointments clauses:

The warranty is required by law during the period from the date of purchase. This must be the basis of a cash card or a payment 
document - the name of the dealer and the date of sale aufscheinen -. 
Customer Services for Sales Territory Austria: It will only be reported in writing customer service jobs, as performed, for example, 
guaranteed rates, or accepted if this is proven by a written message with proof of purchase (cash receipt) ... the service there.  
The warranty covers repairs and replacement of components of the device, which must be recognized by the company 
SANOTECHNIK. The intervention fee is payable by the customer, which is payable directly to the customer service. But not on 
installation and removal, and all other costs, these are excluded. Operational noises do not justify a complaint. 
Excluded from the warranty, defective parts, whose failure to negligence, improper use, use-wear, improper installation, 
maintenance by unlicensed personnel, are due damage in transit, such as backups, for example, decorative elements, etc. 
By poor compliance with the instructions of the manufacturers of any direct or indirect liability declines to persons or property.  
Indirect damage, w. for example, consequential damages due to lack of use or removal of any manufacturer is not liable. 
For repairs after the warranty period, the parts replaced, in work and travel expenses - according to the applicable rates set - into 
account. The current rates of fees, you can ask your customer service. 

–

1 

–