JCD3007
2
•
Be sure to use only round CDs for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to
malfunction.
•
Do not stick paper or tape on the disc. Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers.
•
Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a vehicle parked in direct sunlight where
there can be a considerable rise in temperature inside the vehicle.
NOTE: A disc may become scratched (although not enough to make it unusable) depending on how you handle it and other
conditions in the usage environment. These scratches are not an indication of a problem with the player.
INSTALLATION
Before You Begin
1.
Disconnect Battery
Before you begin, always disconnect the battery negative terminal.
2.
Remove Transport Screws
Important Notes
•
Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.
•
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
•
Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.
•
Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop.
•
If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance.
•
This unit is not waterproof and is intended for interior mounting applications only.
Exterior mounting of the unit requires use of an ASA approved marine housing.
•
Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be
subject to excessive dust, dirt or vibration.
•
Be sure to remove the control panel before installing the unit.
DIN Front/Rear Mount
This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear” (DIN rear mount installation, utilizing threaded
screw holes at the sides of the unit chassis) mount. For details, refer to installation methods A and B.
DIN Front Mount (Method A)
Dashboard
Bend Tabs
Screw Stud
1.
Remove the detachable front panel, if it is attached to the chassis, by pushing the
REL
button.
2.
Slide the mounting sleeve off of the chassis if it has not already been removed. If it is locked into position, use the removal keys
(supplied) to disengage it. The removal keys are depicted in Removing the Unit.
3.
Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as
necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that
there will be sufficient space behind the dashboard for the radio chassis.
4.
Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard
opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.
5.
Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.
6.
Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to
ensure proper operation.
7.
After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (vehicle ignition switch must be
on). If the unit does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn the ignition
switch off and proceed with final mounting of the chassis.
Dashboard
Plain Washer
Screw
Rubber Bushing
Hex Nut
Support Strap
Screw Stud
8.
Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.
9.
Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut and spring
washer provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the
screw and plain washer provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio must be supported with
the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration.
