Sansui SLED4280, Owner'S Manual

18

Memorizing channels

This TV is equipped with a channel memory 

feature which allows channels to skip up or down 

to the next channel set into memory, skipping 

over unwanted channels. Before selecting 

channels, they must be programmed into the 

TV’s memory. To use this TV with an antenna, set 

the Signal Type option to the Air mode. When 

shipped from the factory, this menu option is in 

the Cable mode.

Air/Cable selection

1

Select  “Channel”, then press 

▶

 or 

ENTER

.

2

Press 

▲

 or 

▼

 to select “Auto Ch Memory”, then 

press 

▶

 or 

ENTER

.

3

Press 

▲

 or 

▼

 to select “Signal Type”.

4

Press 

◀

 or 

▶

 to select “Air” or “Cable”.

Air 

- VHF/UHF channels

Cable 

- CABLE TV channels

Automatic Search

Start

Auto Ch Memory

Signal Type

Cable

: Adjust

: Select

CABLE CHART

The chart below is typical of many cable system 

channel allocations.

NOTE:

It may take a few seconds for a digital channel 

picture to appear on screen after being selected.

Automatic Search

1

Select “Channel”, then press 

▶

 or 

ENTER

. 

2

Press 

▲

 or 

▼

 to select “Auto Ch Memory”, then 

press 

▶

 or 

ENTER

.

3

Press 

▲

 or 

▼

 to select “Automatic Search”, then 

press 

▶

 or 

ENTER

.

Auto Ch Memory

Signal Type

Cable

Digital Channel Found : 5

Analog Channel Found : 7

Programming Now

: Select

ENTER:Cancel

Automatic Search

Stop

•

4

The TV will begin memorizing all the channels 

available in your area.

It may take from 15 minutes to 30 minutes to 

complete memorizing digital cable channels.

  Depending on the reception condition, a bar 

display may not advance for several minutes, 

please be patient.

•

NOTE:

Memorizing channels is best accomplished during 

evening “PRIMETIME” hours, as more stations are 

broadcasting digital signals. Memorizing channels can 

only be accomplished while a station is broadcasting 

a digital signal to set that channel into memory. 

If you are unsure of the digital channels available 

in your area, you may visit www.antennaweb.org to 

receive a list based on your address or zip code. 

Should you require further assistance you may call 

our toll-free customer service line at 1-800-289-0980.

New digital channels may be added to your area 

periodically, it is recommended to perform the 

“Automatic Search” procedure regularly.

Adding Channel

If you find a new digital channel unregistered, you can 

add the new channel into the channel memory.

1

Tune in the new channel.

2

Select “Channel”, then press 

▶

 or 

ENTER

.

3

Press 

▲

 or 

▼

 to select “Add/Delete”, then press 

▶

or 

ENTER

.

Add/Delete

>>

Clear All

>>

Add/Delete

Adding Channel

>>

: Select

ENTER:Set

4

Press 

▲

 or 

▼

 to select “Adding Channel”, then 

press 

▶

 or 

ENTER

. The new channel will be 

added into the channel memory.

Add/Delete channel

You can select the channel that you want to skip.

1

Select “Channel”, then press 

▶

 or 

ENTER

.

2

Press 

▲

 or 

▼

 to select “Add/Delete”, then press

▶

 or 

ENTER

.

3

Press 

▲

 or 

▼

 to select “Add/Delete”, then press

▶

 or 

ENTER

.

4

Press 

▲

 or 

▼

 to select the channel that you want 

to skip.

CH

Signal

2

Analog

3

Analog

Add

3-1

Digital

Delete

3-2

Digital

Add

4

Analog

Delete

Add/Delete

: Adjust

Add

: Select

5

Press 

◀

 or 

▶

 to select “Add” or “Delete”, 

whichever function you want to perform.

6

Repeat steps 4 - 5 for other channels you want to 

add or delete.

•

•

•

3CQ0821B_En.indd   18

3CQ0821B_En.indd   18

10/7/10   4:37:25 PM

10/7/10   4:37:25 PM